Interface 9825 Installation & User Manual Download Page 22

Warranty

 

Warranty
All indicator products from Interface  Inc., ('Interface') are warranted against defective material and 

workmanship for a period of (1) one year  from the date of dispatch. If the 

'Interface' product you purchase appears to have a defect in material or workmanship or fails during 

normal use within the period, please contact your Distributor, who will assist you in resolving the 

problem.  If it is necessary to return the product to 'Interface' 

please include a note stating name, company, address, phone number and a detailed description of 

the problem. Also, please indicate if it is a warranty repair. The sender is responsible for shipping 

charges, freight insurance and proper packaging to prevent breakage in transit. 'Interface' warranty 

does not apply to defects resulting from action of the buyer such as mishandling, improper interfacing, 

operation outside of design limits, improper repair or unauthorised modification.  No other warranties 

are expressed or implied. 'Interface' specifically disclaims any implied warranties of merchantability or 

fitness for a specific purpose. The remedies outlined above are the buyer's only remedies. 

'Interface' will not be liable for direct, indirect, special, incidental or consequential damages whether 

based on the contract, tort or other legal theory. 

Any corrective maintenance required after the warranty period should be performed by 

'Interface' approved personnel only

www.interfaceforce.com

Interface Inc. www.interfaceforce.com

19

9825 Installation & User Manual

Summary of Contents for 9825























Reviews: