manualshive.com logo in svg

Inter-m SC-9216R, Operation Manual, Page: 22 / 24

Share
Download
Inter-m SC-9216R Operation Manual Download Page 22

20

SC-9216R

SPEAKER LINE CHECKER

Specifications

Specifications

- ELECTRICAL

Test Impedance Range  ............................................................................................................20

Ω

to 1600

Ω

Test Parameters .............................................................................................................Ground or Earth Fault
Line Open ............................................................................................................. > 125% of reference value
Line Impedance High ................................................................................... 115% to 125% of reference value
Line Impedance Normal .....................................................................................85%-115% of reference value
Line Impedance Low......................................................................................... 75% to 85% of reference value
Line Short ................................................................................................................ < 75% of reference value
Test Duration (per channel) ............................................................................................................< 100msec
Test Interval (selectable) ...................................................................................................1 minute to 24 hours
Number of Channels .................................................................................................................................16
Test Frequency.....................................................................................................................................15kHz
Test Voltage .........................................................................................................................................5VAC
Operating Temperature ................................................................................................................-5°C~40°C

- GENERAL

Power Source...................................................................100–120VAC or 220–240VAC; 50/60Hz, DC 24V

..............................................................

(Supplied AC mains transformer depends on country requirements)

Power Consumption ..............................................................................................................................11W
Weight ....................................................................................................................................5.7kg/12.6lb
Dimensions ........................................................................482(W)x88(H)x280(D)mm/19(W)x3.5(H)x11(D)in

* Specifications and design subject to change without notice.

Summary of Contents for SC-9216R

























Reviews:

No comments