background image

ELECTRONIC CLIMATE CONTROL II 

SERVICE MANUAL Part No’s. 00-00855-000 / 00-00856-000 

 

 

 

Intellitec 

1485 Jacobs Rd.

Deland, FL 32724

386.738.7307

www.Intellitec.com 

- 2 - 

P/N 53-00855-856 Rev. C 080819

 

 
 

How It Works 

 
The System contains two major components, the ECC Thermostat and the ECC Control Module, along with additional 
external sensors which are connected to these modules. 
 

THE ECC THERMOSTAT: 

 
The Thermostat allows the owner to set the air conditioning and heating systems’ modes and temperature.  The 
electronics in this panel measure ambient temperatures via two external temperature probes (front and rear). Based on 
the mode, set point temperature settings, and the temperature measured by the probes, the thermostat sends appropriate 
control signals to the ECC Control Module.  These signals are sent via a two wire multiplexed communication link labeled 
IPX SIG and IPX GND.  The Control Module then operates the air conditioners or furnace as required to maintain the set 
temperature. 

 

HEAT

HEAT

OFF

OFF

LO FAN

LO FAN

HI FAN

HI FAN

LO COOL

LO COOL

HI COOL

HI COOL

AUTO COOL

AUTO COOL

FRONT

BOTH
REAR

FRONT

BOTH
REAR

FURNACES

FURNACES

SHED

SHED

AC 1

AC 1

ON

ON

SHED

SHED

AC 2

AC 2

ON

ON

ELECTRONIC
CLIMATE CONTROL

ELECTRONIC
CLIMATE CONTROL

75

70

TEMPERATURE

SET

TEMPERATURE

SET

 

 

There is a single function switch that controls the functions of the two air conditioner (A/C1) and (A/C2) systems.  The 
potentiometer allows the user to select a desired temperature for the system in the range of 50 to 90 degrees Fahrenheit.  
Moving the controls down lowers the set point temperature.  The seven-position function switch is used to select the 
furnace’s and air conditioners’ operating modes.   
 
A brief description of each mode is as follows: 
 

HEAT - 

The Thermostat controls the furnace/s to maintain the desired temperature in the coach.  The furnace/s will be 
energized when the ambient temperature at the corresponding front or rear temperature probe is 2 degrees below 
the set point temperature and shut off when the ambient temperature is at the set-point temperature.  On single 
furnace versions of the Thermostat (00-00856-_10) the furnace selector switch is not present.  Load shedding is 
not active in this mode. 

 

OFF -  

All control settings are disabled and the Thermostat is placed in a low-current “sleep” mode in order to minimize 
battery drain (35 - 45mA).

 

LOW FAN - 

The air conditioner fans are energized on low speed.  Load shedding is active. 

LOW FAN - 

The air conditioner fans are energized on low speed.  Load shedding is active. 

 

HIGH FAN - 

The air conditioner fans are energized on high speed.  Load shedding is active. 

Summary of Contents for 00-00855-000















Reviews: