IntelliSAW IRM-48 Installation Manual Download | Manualshive

Page: 20 / 28

background image

IntelliSAW IRM-48 Reader

Installation Manual

Page 20 of 28

IRM-48 Reader

910.00371.0001

5

S

ENSOR

I

NSTALLATION

&

S

YSTEM

C

ONFIGURATION

5.1

S

ENSOR

I

NSTALLATION

This manual does not cover specific sensor installation. Please reference the

IntelliSAW

Sensor Installation Manual

for more detail.

5.2

S

YSTEM

C

ONFIGURATION

The Reader requires system configuration for the associated installed temperature sensors, air
interfaces, and humidity sensors. Configuration is performed through the USB port and uses
the IntelliSAW Measurement Configuration Software. Details will not be discussed here, please
refer to the

Configuration Software User Manual

for detailed instructions.

Figure 13: IntelliSAW System Configuration Software

«
...
18
19
20
21
22
...
»

Summary of Contents for IRM-48





























Reviews:

No comments

Related manuals for IRM-48

Brand: Denver Pages: 34

Brand: Leuze Pages: 92

Brand: Partner Pages: 1

Brand: Sun Microsystems Pages: 58

Brand: Obreey Pages: 71

Brand: Grundig Pages: 38

Brand: H&S Pages: 32

Brand: Jensen Pages: 100

Gigabit Ethernet-SX PCI-X Adapter and Dual...

Brand: IBM Pages: 32

Brand: SnowEx Pages: 24

Brand: ICP DAS USA Pages: 8

Brand: a-TroniX Pages: 7

Brand: StarTech.com Pages: 2

Brand: Jamex Pages: 15

Brand: Pyle Pages: 11

Brand: Boss Audio Systems Pages: 2

Brand: Boss Audio Systems Pages: 18

Brand: Kenwood Pages: 34

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands