manualshive.com logo in svg

Intellian v100Ka, Installation And Operation Manual

Share
Download
Intellian v100Ka Installation And Operation Manual Download Page 38

v100Ka – Marine Satellite Communication System

38

Gyrocompass Connection

Connecting the System with a Gyrocompass

The ship’s gyrocompass provides true heading input to the antenna system which 
allows the antenna to target and acquire the desired satellite quickly. Intellian always 
recommends to connect a gyrocompass to the antenna through the gyrocompass  
interface on the ACU. If the ship’s gyrocompass output is other than NMEA 0183 
and NMEA 2000, a separate purchase of an NMEA converter is required.

Recommended Cable

• NMEA 0183 / NMEA 2000 Gyrocompass Cable (Customer supplied)
• Connector Type: 2 conductors for NMEA 0183, 5 conductors for NMEA 2000 
• NMEA heading sentence: xx HDT (4800 Baud, 8, N,1) 

If there is no HDT sentence, then use HDM sentence instead.

• NMEA 2000 heading PGN Number = 127250 (Vessel Heading) 

Gyrocompass connection 

Strip the cable for 5 mm (0.2")
Do not solder the cable

Summary of Contents for v100Ka




























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands