Intellian T240CK Installation And Operation User Manual Download Page 106

Page: 106 / 160

t240CK – Marine Satellite TV Antenna System

106

AutoUpdate

Intellian Aptus

checks and notifies the latest version when it is started to maintain

up to date software version by AutoUpdate function.

1. When Aptus

is started, it automatically checks the latest software version from

the server and runs AutoUpdate if new version is available.

2. Current software version information is displayed.

3. It notifies new software version information.

4. When you click the “start” button, “File downloading…” message is displayed
while downloading files from the server.

5. When file downloading is finished, “installing…” message is displayed and Aptus
patch runs and the installation starts by InstallShield.

6.Click the “Finish” button when InstallShield installation is finished, then “Run
the Aptus” message is displayed and Aptus runs and AutoUpdate is automatically
finished.

Summary of Contents for T240CK

































































































































































Search results

Summary of Contents for T240CK

Reviews:

Related manuals for T240CK

Brands by name

Popular brands

Intellian T240CK, Installation And Operation User Manual

Search results

Summary of Contents for T240CK

Reviews:

Related manuals for T240CK

Brands by name

Popular brands