Intellian T240CK Installation And Operation User Manual Download Page 154 | Manualshive

Page: 154 / 160

background image

t240CK – Marine Satellite TV Antenna System

154

iARM Upgrade

No.

Item

Description

1

iARM Upgrade

Upgrade the firmware of iARM module.

2

New iARM
Firmware

Select a new firmware file and click Start Update button to
upgrade the firmware.

3

Bootstrap
/Bootloader

Displays current bootstrap and bootloader version.

4

Kernel
/File System

ACU has 3 storage parts sys0, sys1, Factory Default
Display kernel and file system version and current activated
part Information.

iARM firmware upgrade procedures:

1. Click on “Browse” button to select the iARM firmware file (.tgz) that you
wish to upgrade.
2. Click on “Start Update” button to update the iARM firmware. Wait until
the page is loaded.
3. It’ll inform you that the firmware is being uploaded.

1

3

4

2

«
...
152
153
154
155
156
...
»

Summary of Contents for T240CK

































































































































































Reviews:

No comments

Related manuals for T240CK

Brand: Outbacker Pages: 3

Brand: TENNADYNE Pages: 12

Brand: Fusion Pages: 4

Brand: Sirio Antenne Pages: 2

Brand: Vision Plus Pages: 2

Brand: Novatel Pages: 2

Pulse LARSEN LM Series

Brand: Yageo Pages: 2

Pulse YA Series

Brand: Yageo Pages: 2

Penetrator SPT-500

Brand: Hy-Gain Pages: 4

Brand: Tri-Americas Pages: 10

Brand: Leica Pages: 41

Brand: Telex Communications Pages: 8

Brand: Mohu Pages: 2

Brand: EAntenna Pages: 13

Brand: Oyster Pages: 16

Brand: camping first Pages: 44

Brand: Kathrein Pages: 4

Brand: DX Engineering Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands