Intellian T240CK Installation And Operation User Manual Download Page 20

Page: 20 / 160

t240CK – Marine Satellite TV Antenna System

Installation and mounting of antenna

The method of installation and mounting of antenna may vary with vessel design but
the following procedures are applicable in most situations, and will result in a secure
and effective installation.

Confirmation of size prior to installation

•

Confirm the height and diameter of the bottom surface of the antenna before

installing it.

•

The space must be sufficient for installing the antenna unit considering the height

and diameter of the antenna.

•

The height and the diameter of the bottom surface of the antenna are as shown

in the following drawing. It is strongly suggested that the installation is conducted
using a crane.

4097mm

3522mm

575mm

3300mm

1868mm

Summary of Contents for T240CK

































































































































































Search results

Summary of Contents for T240CK

Reviews:

Related manuals for T240CK

Brands by name

Popular brands

Intellian T240CK, Installation And Operation User Manual

Search results

Summary of Contents for T240CK

Reviews:

Related manuals for T240CK

Brands by name

Popular brands