background image

2

General Installation Process

The installation instructions in this section are for common components of Intel® Server System 
R2000SC family.

Minimum Hardware Requirements

 

Memory Type:

 

    

Minimum of one 1 GB, 240-pin, RDIMM or UDIMM, DDR3-1066, 

    DDR3-1333, or DDR3-1600.

 

Processor:

    Intel

® 

Xeon

® 

Processor E5-2400 product family.

 

Hard Disk Drives:

 SATA

For a complete list of compatible

 

processors, heatsinks,

 

and memory, see

http://www.intel.com/p/en_US/support

.

To avoid integration difficulties and possible board damage, your system must 

meet the following minimum requirements:

1

Preparing the System

Observe normal ESD (Electrostatic Discharge) 

procedures.

Place your Intel

®

 Server System on a flat anti-static 

surface to perform the following integration procedures. 

Observe ESD procedures before reaching inside to make 

server board connections or install components.

IMPORTANT!

Before proceeding 

further, check your 

Intel

®

 Server System 

for disconnected or 

loose cables and 

components that 

may have occurred 

during shipping.

2

Remove the Top Cover

B

Remove the four screws.

A

A

B

B

Slide the cover backward 

and lift up.

3

Remove the Air Duct

Removing air duct by lifting 

straight up.

4

Remove Processor Heatsink(s)

The heatsink is attached to the server board / processor socket with captive fasteners.

Lift the heatsink straight up.

A

B

C

CAUTION: The heatsink has thermal interface material (TIM) on the underside 

of it.  Use caution so that you do not damage the thermal interface material. 

Use gloves to avoid sharp edges.

Using a #2 Phillips* screwdriver, loosen the four screws located on the 

heatsink corners in a diagonal manner using the following procedure:

Using a #2 Phillips* screwdriver, start with screw 1 and loosen it by 

giving it two rotations and stop. (IMPORTANT: Do not fully loosen.) 
Proceed to screw 2 and loosen it by giving it two rotations and stop. 

Similarly, loosen screws 3 and 4. 
Repeat steps A and B by giving each screw two rotations each time 

until all screws are loosened.

Processor

Soc

ket

AIRFLOW

Chassis Front

2

3

1

4

A

B

C

Summary of Contents for R2000SC





















Reviews: