Intel DB85FL Specification Download Page 56

Page: 56 / 84

Intel Desktop Board DB85FL Technical Product Specification

CAUTION

Ensure that the ambient temperature does not exceed the board’s maximum operating

temperature. Failure to do so could cause components to exceed their maximum case

temperature and malfunction. For information about the maximum operating

temperature, see the environmental specifications in Section 2.8.

CAUTION

Ensure that proper airflow is maintained in the processor voltage regulator circuit.

Failure to do so may result in damage to the voltage regulator circuit. The processor

voltage regulator area (shown in Figure 15) can reach a temperature of up to 120

C in

an open chassis.

Figure 15 shows the locations of the localized high temperature zones.

Item

Description

Processor voltage regulator area

Processor

Intel B85 Express Chipset

Figure 15. Localized High Temperature Zones

Summary of Contents for DB85FL





















































































Search results

Summary of Contents for DB85FL

Reviews:

Related manuals for DB85FL

Brands by name

Popular brands

Intel DB85FL, Specification

Search results

Summary of Contents for DB85FL

Reviews:

Related manuals for DB85FL

Brands by name

Popular brands