Intel DB85FL Specification Download Page 28

Page: 28 / 84

Intel Desktop Board DB85FL Technical Product Specification

•

LinkSec offload compliant with 802.3ae specification

•

TimeSync offload compliant with 802.1as specification

Power Management Features:

•

Magic Packet* wake-up enable with unique MAC address

•

ACPI register set and power down functionality supporting D0 and D3 states

•

Full wake up support (APM, ACPI)

•

MAC power down at Sx, DMoff with and without WoL

•

Auto connect battery saver at S0 no link and Sx no link

•

Energy Efficient Ethernet (EEE) support

•

Latency Tolerance Reporting (LTR)

•

Optimized Buffer Flash/Fill (OBFF) support

•

ARP and ND proxy support through LAN Connected Device proxy

•

Wake on LAN (WoL) from Deep Sx

•

Provides lower power usage to meet ENERGY STAR 5.2 and ErP specifications

1.9.2

LAN Subsystem Software

LAN software and drivers are available from Intel’s World Wide Web site.

For information about

Refer to

Obtaining LAN software and drivers

http://downloadcenter.intel.com

1.9.3

RJ-45 LAN Connector with Integrated LEDs

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 5).

Item Description

Link LED (Green)

Data Rate LED (Green/Yellow)

Figure 5. LAN Connector LED Locations

Summary of Contents for DB85FL





















































































Search results

Summary of Contents for DB85FL

Reviews:

Related manuals for DB85FL

Brands by name

Popular brands

Intel DB85FL, Specification

Search results

Summary of Contents for DB85FL

Reviews:

Related manuals for DB85FL

Brands by name

Popular brands