Intel BLKDH55PJ Product Manual Download Page 9

Page: 9 / 76

1 Desktop Board Features

This chapter briefly describes the features of Intel

Desktop Board DH55PJ. Table 1

summarizes the major features of the Desktop Board.

Table 1. Feature Summary

Form Factor

MicroATX (243.84 millimeters [9.60 inches] x 243.84 millimeters
[9.60 inches])

Processor

•

Intel

Core™ i7, Intel

Core™ i5, Intel

Core™ i3 and Intel

Pentium processors in an LGA1156 socket:

―

Integrated graphics processing (processors with Intel® Graphics
Technology)

―

External graphics interface controller

―

Integrated memory controller

Chipset

Intel

H55 Express Chipset consisting of the Intel

H55 Express

Platform Controller Hub (PCH)

Memory

•

Two 240-pin DDR3 SDRAM Dual Inline Memory Module (DIMM)
sockets

•

Support for DDR3 1333 MHz and DDR3 1066 MHz DIMMs

•

Support for 1 Gb and 2 Gb memory technology

•

Support for up to 8 GB of system memory with two DIMMs using
2 Gb memory technology

•

Support for non-ECC memory

Graphics

•

Integrated graphics support for processors with Intel Graphics

Technology:

―

VGA

―

DVI-D

•

Discrete graphics support for PCI Express* 2.0 x16 add-in graphics

card

Audio

Intel

High Definition Audio via the Realtek* ALC888S audio codec

Expansion
Capabilities

•

One PCI Express 2.0 x16 add-in card connector

•

Two PCI Express 2.0 x1 add-in card connectors

•

One PCI* bus connector

continued

Summary of Contents for BLKDH55PJ













































































Search results

Summary of Contents for BLKDH55PJ

Reviews:

Related manuals for BLKDH55PJ

Brands by name

Popular brands

Intel BLKDH55PJ, Product Manual

Search results

Summary of Contents for BLKDH55PJ

Reviews:

Related manuals for BLKDH55PJ

Brands by name

Popular brands