manualshive.com logo in svg

Intel BLKDH55PJ, Product Manual, Page: 23 / 76

Share
Download
Intel BLKDH55PJ Product Manual Download Page 23

Desktop Board Features 

23 

+5 V Standby Power Indicator LED 

 CAUTION 

If the AC power has been switched off and the standby power indicator is still lit, 
disconnect the power cord before installing or removing any devices connected to the 
board.  Failure to do so could damage the board and any attached devices. 

 

The Desktop Board’s standby power indicator, shown in Figure 3, is lit when there is 
standby power still present on the board even when the computer appears to be off.  
For example, when this green LED is lit, standby power is still present at the memory 
module sockets and the PCI bus connectors.  

 

Figure 3.  Location of the Standby Power Indicator 

For more information on standby current requirements for the Desktop Board, refer to 
the Technical Product Specification at 

http://support.intel.com/support/motherboards/desktop/

 

Wake from USB 

 

NOTE 

Wake from USB requires the use of a USB peripheral that supports Wake from USB 
and an operating system that supports Wake from USB. 

 

USB bus activity wakes the computer from an ACPI S1 or S3 state. 

PCI PME# Signal Wake-up Support 

When the PME# signal on the PCI bus is asserted, the computer wakes from an 
ACPI S1, S3, S4, or S5 state. 

Summary of Contents for BLKDH55PJ













































































Reviews:

No comments