manualshive.com logo in svg

Intel BLKDH55PJ, Product Manual, Page: 47 / 76

Share
Download
Intel BLKDH55PJ Product Manual Download Page 47

Installing and Replacing Desktop Board Components 

47 

Serial Header 

Figure 20, H shows the location of the serial header.  Table 12 shows the pin 
assignments and signal names for the serial header. 

Table 12. Serial Port Header 

Pin 

Signal Name 

Pin 

Signal Name 

1 

DCD (Data Carrier Detect) 

2 

RXD# (Receive Data) 

3 

TXD# (Transmit Data) 

4 

DTR (Data Terminal Ready) 

5 

Ground 

6 

DSR (Data Set Ready) 

7 

RTS (Request To Send) 

8 

CTS (Clear To Send) 

9 

RI (Ring Indicator) 

10 

Key (no pin) 

 

Connecting to the Audio System 

After installing the Realtek audio driver from the Intel

®

 Express Installer DVD-ROM, 

the multi-channel audio feature can be enabled.  Figure 21 shows the back panel audio 
connectors.  The default connector assignments are shown in the table.   

 

Item Description 
A Line 

in 

B 

Line out (front speaker/headphones) 

C Mic 

in 

Figure 21.  Back Panel Audio Connectors  

 

NOTE 

The back panel line out connector is designed to power either headphones or amplified 
speakers only.  Poor audio quality may occur if passive (non-amplified) speakers are 
connected to this output. 

Summary of Contents for BLKDH55PJ













































































Reviews:

No comments