manualshive.com logo in svg

Intel BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard, Technical Product Specification, Page: 43 / 80

Share
Download
Intel BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard Technical Product Specification Download Page 43

Technical Reference 

 43

 

2.2.2.4

 

Front Panel Header 

This section describes the functions of the front panel header.  Table 18 lists the signal 
names of the front panel header.  Figure 10 is a connection diagram for the front panel 
header. 

Table 18. Front Panel Header 

 
Pin 

 
Signal 

In/ 
Out 

 
Description 

 
Pin 

 
Signal 

In/ 
Out 

 
Description 

Hard Drive Activity LED 

[Yellow] 

Power LED 

[Green] 

1 

HD_PWR 

Out 

Hard disk LED 
pull-up  to +5 V 

2 HDR_BLNK_ 

GRN 

Out 

Front panel green 
LED 

3 

HDA# 

Out 

Hard disk active 
LED 

4 HDR_BLNK_ 

YEL 

Out 

Front panel yellow 
LED 

Reset Switch 

[Purple] 

On/Off Switch 

[Red] 

5 Ground   

Ground 

6  FPBUT_IN 

In  Power 

switch 

7 FP_RESET# 

In  Reset 

switch 

8  Ground 

 

Ground 

Power Not 

Connected 

9 

+5 

V   Power 

10 

N/C 

 Not 

connected 

 

 

Figure 10.  Connection Diagram for Front Panel Header 

 

Summary of Contents for BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard

















































































Reviews:

No comments