manualshive.com logo in svg

Intel BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard, Technical Product Specification, Page: 24 / 80

Share
Download
Intel BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard Technical Product Specification Download Page 24

Intel Desktop Board D945GCPE Technical Product Specification 

24 

 

1.8.2

 

Realtek RTL8101E-GR Fast Ethernet Controller 

The Realtek RTL8101E-GR provides the following functions: 

•

 

10/100 Ethernet LAN connectivity 

•

 

Full device driver compatibility 

•

 

Programmable transit threshold 

•

 

Configuration EEPROM that contains the MAC address 

1.8.2.1

 

RJ-45 LAN Connector with Integrated LEDs 

Two LEDs are built into the RJ-45 LAN connector (shown in Figure 4).   

 

Figure 4.  LAN Connector LED Locations 

Table 4 describes the LED states when the board is powered up and the 
10/100 Mbits/sec LAN subsystem is operating. 

Table 4.  LAN Connector LED States 

LED 

LED Color 

LED State 

Condition 

Off 

LAN link is not established. 

On 

LAN link is established. 

A Green 

 

Blinking 

LAN activity is occurring. 

Off 

10 Mbits/sec data rate is selected. 

B Yellow 

On 

100 Mbits/sec data rate is selected. 

Summary of Contents for BLKD945GCPE - LGA775 1066FSB 2DDR2 2GB Audio Video Lan mATX 10Pack Motherboard

















































































Reviews:

No comments