51
En
Speaker Configuration
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify “
Full Band
” for speakers that can output low fre-
quency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover fre-
quency will be output by the subwoofer instead of the
speaker. Refer to your speaker’s manuals to determine the
optimum crossover frequencies. If you set up your speak-
ers using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any THX
speakers are set to “
80Hz(THX)
” crossover.
■
Subwoofer
Yes
:
Select if a subwoofer is connected.
No
:
Select if no subwoofer is connected.
■
Front
Full Band
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
to
130Hz
,
150Hz
,
200Hz
Note
• If the “
Subwoofer
” setting is set to “
No
”, the “
Front
” setting is
fixed at “
Full Band
”.
■
Center
*1
, Surround
*1
, Surr Back
*2*3*4*5
Full Band
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
to
130Hz
,
150Hz
,
200Hz
None
:
Select if no speaker is connected.
■
Front Wide
*1*2*4*6
, Front High
*1*2*4*5
Full Band
40Hz
,
45Hz
,
50Hz
,
55Hz
,
60Hz
,
70Hz
,
80Hz(THX)
to
130Hz
,
150Hz
,
200Hz
None
:
Select if no speaker is connected.
Note
*1
“
Full Band
” can be selected only when “
Full Band
” is
selected in the “
Front
” setting.
*2
If the “
Surround
” setting is set to “
None
”, this setting cannot
be selected.
*3
If the “
Surround
” setting is set to anything other than “
Full
Band
”, “
Full Band
” cannot be selected here.
*4
If the “
Speakers Type(Front)
” setting is set to “
Bi-Amp
”
), this setting cannot be selected.
*5
If the Powered Zone 2 is being used (
), this setting can-
not be selected.
*6
If the “
Powered Zone 2
” setting is set to
“
Act
”
(
), this
setting cannot be selected.
■
Surr Back Ch
1ch
:
Select if only one surround back speaker is con-
nected.
2ch
:
Select if two (left and right) surround back speakers
are connected.
Note
• If the “
Surr Back
” setting is set to “
None
” (
), this setting
cannot be selected.
■
LPF of LFE
(Low-Pass Filter for the LFE Channel)
80Hz
,
90Hz
,
100Hz
,
110Hz
,
120Hz
With this setting, you can specify the cutoff frequency
of the LFE channel’s low-pass filter (LPF), which can
be used to filter out unwanted hum. The LPF only
applies to sources that use the LFE channel.
■
Double Bass
With the Double Bass function, you can boost bass out-
put by feeding bass sounds from the front left, right, and
center channels to the subwoofer.
On
:
Double Bass function on.
Off(THX)
:
Double Bass function off.
Note
• This function can be set only if the “
Subwoofer
” setting is set to
“
Yes
”, and the “
Front
” setting is set to “
Full Band
”.
• If you’re using THX-certified speakers, select “
Off(THX)
”.
This setting is set automatically by Audyssey MultEQ
®
Room Correction and Speaker Setup function (
).
This setting is NOT set automatically by
Audyssey MultEQ Room Correction and Speaker Setup
function (