Integra DTR-20.3, Instruction Manual

Page: 48 / 92

48
En
Main menu Audio Adjust
With the Audio Adjust functions and settings, you can
adjust the sound and listening modes as you like.
Multiplex/Mono
■
Multiplex
Input Channel
`
Main
`
Sub
`
Main/Sub
This setting determines which channel of a stereo
multiplex source is output. Use it to select audio channels
or languages with multiplex sources, multilingual TV
broadcasts, and so on.
■
Mono
Input Channel
`
Left + Right
`
Left
`
Right
This setting specifies the channel to be used for playing
any 2-channel digital source such as Dolby Digital, or 2-
channel analog/PCM source in the Mono listening mode.
Output Speaker
`
Center :
Mono audio is output by the center speaker.
`
Left / Right :
Mono audio is output by the front left and right
speakers.
This setting determines which speakers output mono
audio when the Mono listening mode is selected.
Note
• If the “ Center ” setting is set to “ None ” (
➔
page 45 ), this
setting cannot be selected.
Dolby
■
PL IIx Music (2ch Input)
These settings apply to only 2-channel stereo sources.
If you’re not using any surround back speakers, these
settings apply to Dolby Pro Logic II, not Dolby Pro Logic
IIx.
Panorama
`
On
`
Off
With this setting, you can broaden the width of the front
stereo image when using the Dolby Pro Logic IIx Music
listening mode.
Dimension
`
–3 to 0 to +3
With this setting, you can move the sound field forward or
backward when using the Dolby Pro Logic IIx Music
listening mode. Higher settings move the sound field
backward. Lower settings move it forward.
If the stereo image feels too wide, or there’s too much
surround sound, move the sound field forward to improve
the balance. Conversely, if the stereo image feels like it’s
in mono, or there’s not enough surround sound, move it
backward.
Center Width
`
0 to 3 to 7
With this setting, you can adjust the width of the sound
from the center speaker when using the Dolby Pro Logic
IIx Music listening mode. Normally, if you’re using a
center speaker, the center channel sound is output from
only the center speaker. (If you’re not using a center
speaker, the center channel sound will be distributed to the
front left and right speakers to create a phantom center).
This setting controls the front left, right, and center mix,
allowing you to adjust the weight of the center channel
sound.
■
PL IIz Height Gain
`
Low
`
Mid
`
High
The Height Gain Control in Dolby Pro Logic IIz enables
the listener to select how much gain is applied to the front
high speakers. There are three settings, “
Low ”, “ Mid ” and
“ High ”, and the front high speakers are accentuated in that
order. While “ Mid ” is the default listening setting, the
listener may adjust the Height Gain Control to their
personal preference.
Note
• If the “ Front High ” settings is set to “ None ” (
➔
page 45 ), this
setting cannot be selected.
■
Dolby EX
Dolby EX
`
Auto :
If the source signal contains a Dolby EX flag, the
Dolby EX or THX Surround EX listening mode is
used.
`
Manual :
You can select any available listening mode.
This setting determines how Dolby EX encoded signals
are handled. This setting is unavailable if no surround
back speakers are connected. This setting is effective with
Dolby Digital, Dolby Digital Plus and Dolby TrueHD
only.
Note
• If the “ Surround Back ” setting is set to “ None ” (
➔
page 45 ),
this setting cannot be selected.
• If the “ Front High ” setting is enabled (
➔
page 45
), this setting
is fixed at “ Manual ”.
Audio Adjust