Integra DHC-80.2, Instruction Manual

Page: 56 / 116

56
En
Equalizer Settings
With the Equalizer settings, you can adjust the tone of
speakers individually with a 15-band equalizer. The vol-
ume of each speaker can be set (
➔
55 ).
■
Equalizer
`
Manual :
You can adjust the equalizer for each speaker manu-
ally. If you selected “
Manual ”, continue with this
procedure.
`
Audyssey :
This is selected automatically by
Audyssey MultEQ XT32 Room Correction and
Speaker Setup function. The
Audyssey indicator will
light (
➔
9
) and “ Dynamic EQ ” (
➔
59
) and
“ Dynamic Volume ” (
➔
60
) become available.
When “ Audyssey ” is selected, “ Dolby Volume ”
becomes “ Off ” automatically (
➔
58
).
`
Off :
Tone off, response flat.
THX Audio Setup
With the “ Surr Back Speaker Spacing ” setting, you can
specify the distance between your surround back speakers.
If you’re using a THX-certified subwoofer, set the “
THX
Ultra2/Select2 Subwoofer ” setting to “ Yes ”. You can
then apply THX’s Boundary Gain Compensation (BGC)
to compensate the perceived exaggeration of low frequen-
cies for listeners sitting very close to a room boundary
(i.e., wall).
You can also set the THX Loudness Plus. When the
“
Loudness Plus ” is set to “ On ”, it is possible to enjoy
even subtle nuances of audio expression at low volume.
This result is only available when the THX listening mode
is selected.
■
Surr Back Speaker Spacing
`
< 1ft (< 0.3m ):
Select this if your surround back speakers are
between 0 and 1 foot (0–30 cm) apart.
`
1ft - 4ft (0.3m - 1.2m) :
Select this if your surround back speakers are
between 1 and 4 feet (0.3–1.2 m) apart.
`
> 4ft (> 1.2m) :
Select this if your surround back speakers are more
than 4 feet (1.2 m) apart.
Note
• Cannot be set if “ Surround Back Ch ” is set to “ 1ch ” (
➔
55
) or
“ Surround Back ” is set to “ None ” (
➔
54 ).
■
THX Ultra2/Select2 Subwoofer
`
No :
Select this if you do not have a THX-certified sub-
woofer.
`
Yes :
Select this if you have a THX-certified subwoofer.
Note
• If the “ Subwoofer ” setting is set to “ No ”, this setting cannot be
selected (
➔
54 ).
■
BGC
`
Off :
Select this to turn off BGC.
`
On :
Select this to turn on BGC.
Note
• This setting is only available if “ THX Ultra2/Select2 Sub-
woofer ” is set to “ Yes ”.
■
Loudness Plus
`
Off :
Select this to turn off Loudness Plus.
`
On :
Select this to turn on Loudness Plus.
This setting is set automatically by
Audyssey MultEQ
® XT32 Room Correction and
Speaker Setup function (
➔
29 ).
1
Press
w
to select “Channel”, and then use
e
/
r
to select a speaker.
2
Use
q
/
w
to select a frequency, and then use
the
e
/
r
to adjust the level at that frequency.
The volume at each frequency can be adjusted
from
–6dB to 0dB to +6dB in 1 dB steps.
Note
• You can select: “ 25Hz ”, “ 40Hz ”, “ 63Hz ”,
“ 100Hz ”, “ 160Hz ”, “ 250Hz ”, “ 400Hz ”, “ 630Hz ”,
“ 1000Hz ”, “ 1600Hz ”, “ 2500Hz ”, “ 4000Hz ”,
“ 6300Hz ”, “ 10000Hz ”, or “ 16000Hz ”. And for the
subwoofer, “ 25Hz ”, “ 40Hz ”, “ 63Hz ”, “ 100Hz ”, or
“ 160Hz ”.
• While the Direct listening mode is selected, the
equalizer settings have no effect.
Tip
• Low frequencies (e.g., 63Hz) affect bass sounds;
high frequencies (e.g., 16000Hz) affect treble
sounds.
3
Use
q
to select “Channel”, and then use
e
/
r
to select another speaker.
Repeat steps 1 and 2 for each speaker.
You cannot select speakers that you set to “
No ”
or “ None ” in the “ Speaker Configuration ”
(
➔
54 ).