background image

Page 14 of 14  

         

2982-222 - Rev: 1/21/2014 8:34 AM 

 

 

Certification and Warranty 

Certification 

This product has been thoroughly tested by ITS ETL SEMKO, a nationally recognized independent third-party testing laboratory. The North American 
ETL Listed mark signifies that the device has been tested to and has met the requirements of a widely recognized consensus of U.S. and Canadian 
device safety standards, that the manufacturing site has been audited, and that the manufacturer has agreed to a program of quarterly factory follow-
up inspections to verify will continued conformance.  

FCC and Industry Canada Compliance Statement 

This device complies with FCC Rules Part 15 and Industry Canada RSS-210 (Rev. 7). Operation is subject to the following two conditions: 

(1) This device may not cause harmful interference, and  

(2) This device must accept any interference, including interference that may cause undesired operation of the device. 

Le present appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorise aux deux 
conditions suivantes :  

(1) l’appareil ne doit pas produire de brouillage, et  

(2) l’utilisateur de l’appareil doit accepter tout brouillage radiolectrique subi, mme si  le brouillage est susceptible d’en compromettre le 

fonctionnement. 

The digital circuitry of this device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. 
These limits are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates, uses, 
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and 
television reception. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such 
interference, which can be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following 
measures: 

-  Re-orient or relocate the receiving antenna of the device experiencing the interference 
-  Increase the distance between this device and the receiver 
-  Connect the device to an AC outlet on a circuit different from the one that supplies power to the receiver 
-  Consult the dealer or an experienced radio/TV technician 

WARNING: Changes or modifications to this device not expressly approved by the party responsible for compliance could void the user’s authority to 
operate the equipment.  
 

ETL/UL Warning (Safety Warning) 
CAUTION: 

To reduce the risk of overheating and possible damage to other equipment, do not install this device to control a receptacle,  a motor-

operated appliance, a fluorescent lighting fixture, or a transformer-supplied appliance.  
Gradateurs commandant une lampe a filament de tungstene –  afin de reduire le risqué de surchauffe et la possibilite d’endommagement a d’autres 
materiels, ne pas installer pour commander une prise, un appareil a moteur, une lampe fluorescente ou un appareil alimente par un transformateur.  

Limited Warranty 

Seller warrants to the original consumer purchaser of this product that, for a period of two years from the date of purchase,  this product will be free 
from defects in material and workmanship and will perform in substantial conformity to the description of the product in this Owner’s Manual. This 
warranty shall not apply to defects or errors caused by misuse or neglect. If the product is found to be defective in material or workmanship, or if the 
product does not perform as warranted above during the warranty period, Seller will either repair it, replace it, or refund the purchase price, at its 
option, upon receipt of the product at the address below, postage prepaid, with proof of the date of purchase and an explanation of the defect or error. 
The repair, replacement, or refund that is provided for above shall be the full extent of Seller’s liability with respect to this product. For repair or 
replacement during the warranty period, call the INSTEON Gold Support line at 800-762-7845 with the Model # and Revision # of the device to receive 
an RMA# and send the product, along with all other required materials to:  

 
INSTEON 
ATTN: Receiving 
16542 Millikan Ave. 
Irvine, CA 92606-5027 

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or 
merchantability or fitness for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, 
which may not be disclaimed or supplanted as provided above shall be limited to the two-year of the express warranty above. No other representation 
or claim of any nature by any person shall be binding upon Seller or modify the terms of the above warranty and disclaimer.  
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify 
the device state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including 
without limitation damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of 
such damages. Some states do not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case 
the above limitations and/or exclusions may not apply to you. You may also have other legal rights that may vary from state to state.  

Protected under U.S. and foreign patents (see 

www.insteon.com

© Copyright 2013 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022, 

www.insteon.com 

 

Summary of Contents for 2982-222















Reviews: