background image

 

Page 16 of 16 

2453-222/2453-422/2453-522 - Rev: 1/21/2014 7:51 AM  

Limitations 

The above warranty is in lieu of and Seller disclaims all other warranties, whether oral or written, express or implied, including any warranty or merchantability or fitness 
for a particular purpose. Any implied warranty, including any warranty of merchantability or fitness for a particular purpose, which may not be disclaimed or supplanted 
as provided above shall be limited to the two-year of the express warranty above. No other representation or claim of any nature by any person shall be binding upon 
Seller or modify the terms of the above warranty and disclaimer.  
Home automation devices have the risk of failure to operate, incorrect operation, or electrical or mechanical tampering. For optimal use, manually verify the device 
state. Any home automation device should be viewed as a convenience, but not as a sole method for controlling your home.  

In no event shall Seller be liable for special, incidental, consequential, or other damages resulting from possession or use of this device, including without limitation 
damage to property and, to the extent permitted by law, personal injury, even if Seller knew or should have known of the possibility of such damages. Some states do 
not allow limitations on how long an implied warranty lasts and/or the exclusion or limitation of damages, in which case the above limitations and/or exclusions may not 
apply to you. You may also have other legal rights that may vary from state to state.  

U.S Patent No. 7,345,998, International patents pending 
© Copyright 2011 INSTEON, 16542 Millikan Ave., Irvine, CA 92606, 866-243-8022

www.insteon.com

 

Summary of Contents for 2453-222

















Reviews: