InstantEye Mk-3 GEN4-D1 Product Manual Download Page 44

Page: 44 / 68

InstantEye Mk-3 GEN4-D1 sUAS Technical Manual

Revision M1.2

August 14, 2019

ITAR or EXPORT CONTROLLED

Page 44

4.7. Collision Imminent and Unavoidable

Indicator: The operator has determined that a collision is imminent and is not possible to

avoid through aircraft maneuvers. There is no on-screen warning indicator for this.

Response Action: Press the

MOTOR

button to shut down aircraft motors. The aircraft’s

low terminal velocity and mass reduce the likelihood of damage as long as the motors are

turned off. Locate the aircraft and collision site as soon as possible to assess any damage.

Leave the GCS powered on so that aircraft location graphic and range/bearing graphic

can assist in location of the crash site. Power down the aircraft immediately upon

recovery.

4.8. GCS-D is Powered Off While Aircraft is in Flight

Indicator: The GCS-D power is turned off, either due to the

POWER

button being pressed,

removal of the battery, or low battery voltage.

Response Action: If the GCS-D shut down due to low battery voltage, replace the dead

battery with a charged one. Put the GCS-D in rescue mode by pressing and holding the

UTILITY 2

and

HOME

buttons while powering on the GCS-D. Rescue mode enables the

GCS-D to skip the pairing configuration steps at boot-up and reinitialize with the flying

aircraft, and then full control can be regained.

4.9. High Wind

Indicator: Aircraft is unable to hold position or make headway against the wind. There is

no on-screen warning indicator for this.

Response Action: Land immediately using video from camera pointed in downward-facing

position. Leave the GCS powered on so that aircraft location graphic and range/bearing

graphic can assist in location of the crash site. Power down the aircraft immediately upon

recovery.

Summary of Contents for Mk-3 GEN4-D1





































































Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands

InstantEye Mk-3 GEN4-D1, Product Manual

Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands