InstantEye Mk-3 GEN4-D1 Product Manual Download Page 18

Page: 18 / 68

InstantEye Mk-3 GEN4-D1 sUAS Technical Manual

Revision M1.2

August 14, 2019

ITAR or EXPORT CONTROLLED

Page 18

3.1.3.1. Joysticks

There are two, four-position joysticks used to reposition the aircraft once it is airborne:

•

The left joystick is the translation joystick. Pushing the translation joystick forward

moves the aircraft forward. Likewise, pushing the translation joystick rearward,

moves the aircraft backward. Pushing the translation joystick left or right moves

the aircraft laterally, left and right.

•

The right joystick is the yaw/altitude joystick. Pushing the yaw/altitude joystick left

or right rotates the aircraft heading (yaw). Pushing the yaw/altitude joystick forward

increases the aircraft altitude and pushing the yaw/altitude joystick rearward

decreases the aircraft altitude.

3.1.3.2. Camera Wheel

There is a wheel on the left underside of the GCS-D. This wheel gimbles the camera.

3.1.3.3. Primary Control Buttons

The ten control buttons and their function are as follows:

•

ALT

button enables and disables Altitude Control

mode

•

NAV

button enables and disables Navigation Control mode

•

CAMERA

button toggles the current video feed that is displayed on the GCS

•

MOTOR

button turns the aircrafts motors on and off

•

HOME

button enables Home mode

•

UTILITY 1

button tilts the gimbaled camera upward

•

UTILITY 2

button tilts the gimbaled camera downward

•

UTILITY 3

button controls payload functions

•

UTILITY 4

button controls payload functions

•

POWER

button turns the GCS-D on/off

3.1.4. Flight Modes Overview

A brief description of the flight modes is given below to provide context for describing

other aspects of the aircraft. A full description of the modes will follow in the section titled

“Flight Modes.” Note the three standard, user-defined modes are shown throughout this

document with black text with green background.

•

Navigation –

Navigation, or

NAV

mode activates the GPS translational position

controller.

•

Altitude

– Altitude, or

ALT

mode activates the vertical position controller.

•

Home

– Home, or

HOME

mode commands the aircraft to return to its home

location.

•

Landing

– Landing mode lands the aircraft at its home location during lost

communications. Landing mode can be activated by holding down the HOME

button.

•

Lost Communications

– Lost communications mode is enabled automatically

when the aircraft fails to receive commands from the GCS. Note, this is not a

user-activated mode.

Summary of Contents for Mk-3 GEN4-D1





































































Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands

InstantEye Mk-3 GEN4-D1, Product Manual

Search results

Summary of Contents for Mk-3 GEN4-D1

Reviews:

Related manuals for Mk-3 GEN4-D1

Brands by name

Popular brands