background image

 

1

 

Safety Instructions 

1.1

 

Warnings 

Please be advised to follow the instructions below for safety. Failure to do so could 
result in potential dangers that may cause property loss, personal injury or death. 

 

The power supplies in the system may produce high voltages and energy 
hazards that may cause personal injury. For your safety, please do not attempt 
to remove the cover of the system to dissemble or replace any component on 
your own. Unless informed by Inspur, only service technicians trained by Inspur 
are authorized to do so. 

 

Please connect the equipment to an appropriate power supply. Use only the 
external power supplies indicated on the rated input label to power the system. 
To protect your equipment from damages caused by a momentary spike or 
plunge of the voltage, please use voltage stabilizing equipment or 
uninterruptible power supplies. 

 

Do not connect two or more power cords to each other. If a longer power cord 
is needed, contact Inspur Customer Service. 

 

Please be sure to use the power supply components that come with the server, 
such as power cords, power socket (if provided with the server) etc. For your 
safety and safety of the equipment, please do not replace power cords or 
plugs randomly. 

 

To prevent electric shocks caused by leakage in the system, please make sure 
that the power cables of the system and peripherals are correctly connected to 
the earthed/grounded outlet. Please connect the three-core power plug to the 
three-core AC power outlet that is well earthed and within reach. Be sure to use 
the earthing/grounding pin of power cord and do not use the patch plug or the 
earthing/grounding pin unplugged with cables. In the case that the 
earthing/grounding conductors are not installed and it is uncertain whether 
there is appropriate earthing/grounding protection, please do not use or 
attempt to operate the equipment. You can contact and consult an electrician. 

 

Please do not push any objects into the openings of the system. Doing so may 
cause short circuit of internal components and then lead to fire or electric 
shock. 

 

Please keep the system far away from the heatsink and heat sources, and be 
sure not to block the air vents. 

 

Please be sure not to scatter food or spill liquid into the system or onto other 
components. Do not use the product in high humid or dusty environments. 

Summary of Contents for NF5280M6





































































































Reviews: