Inspur AS500H User Manual Download Page 31 | Manualshive

Page: 31 / 56

background image

Linux Red Hed 5 Client and SUSE desktop 10:

Only SANtricity client software package is supported, while other software packages such as

RDAC multipath software are not supported, and SANtricity installed on these two systems could
only be used as a storage management workstation.

Red Hat Enterprise Linux and SUSE Linux Enterprise Server:

These two operation systems support RDAC multipath software, as well as SteelEye

LifeKeeper, Novell Open Enterprise Server (OES) and Native Red Hat Clustering software.
(RHLE 4 does not support SteelEye LifeKeeper under IA64 architecture)

9.4

Installation environment requirement

Operation System

System Edition

Windows XP

x86-based system (32-bit and 64-bit)
Pentium or greater CPU or equivalent (233 MHz minimum)
Professional Service Pack 2 (SP2) or later
Note: Only storage management workstation is supported.

Windows server

2003

x86-based system (IA32, Intel Xeon, and 32-bit or 64-bit AMD Opteron)
IA64
Standard Edition, Enterprise Edition, SP 2
SP 1 or x64 Edition (64-bit x86-based system only)

Windows Vista

x86-based system (32-bit and 64-bit)
Pentium or greater CPU or equivalent (800 MHz minimum)
Business Edition or higher

Note:

Only storage management workstation is supported.

Windows server

2008

x86-based system (IA32, Intel Xeon, and 32-bit or 64-bit AMD Opteron)
IA64
Standard (Server Core) Edition, Enterprise (Server Core) Edition,
Web Edition

Linux

x86 (32-bit and 64-bit)
IA64
PowerPC processor (IBM only)
Red Hat Enterprise Linux 4.0 Update 6
Red Hat Enterprise Linux 5.0 Update 1
SUSE Linux Enterprise Server 9.0 UP 4, 10 SP 1
Red Hat 5.0 Client (only storage management workstation)
SUSE Linux Enterprise Desktop 10 (only storage management workstation)

HP-UX

IA64
PA-RISC
11.23, 11.31

AIX

Power PC processor
5.2, 5.3, 6.1

Solaris

SPARC-based system
x86-based system (Intel Xeon, and 32-bit or 64-bit AMD Opteron)

«
...
29
30
31
32
33
...
»

Summary of Contents for AS500H

























































Reviews:

No comments

Related manuals for AS500H

Brand: ICP Pages: 14

Brand: Campbell Pages: 46

Brand: HYVE Pages: 22

Brand: Angel Cool Pages: 2

Brand: QNAP Pages: 74

Brand: StorCentric Pages: 53

Brand: Abocom Pages: 63

Brand: Conel Pages: 32

RS/6000 7043 260

Brand: IBM Pages: 322

Brand: TP-Link Pages: 2

Brand: Airlinkplus Pages: 24

@server xSeries 343

Brand: IBM Pages: 193

Stack On GC-500-5

Brand: Security + Pages: 12

Brand: Billion Pages: 16

SuperServer 1029P-MT

Brand: Supermicro Pages: 123

Brand: TP-Link Pages: 182

220-420LTO - QUICK

Brand: TANDBERG Pages: 8

ICPE2600 Series

Brand: 3onedata Pages: 5

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands