Inspur AS500H User Manual Download Page 2

Page: 2 / 56

Dear users of Inspur server:

Sincerely thank you for selection of Inspur server!

This manual introduces the technical characteristics and the system installation, setup and

usage of Inspur storage system, and helps you to particularly understand and expediently use this

storage system.

Please deliver the package of our product to the waste recycling station for recycling, in favor

of pollution prevent and benefit the humankind.

This manual is the property of the Inspur Company.

This User Manual is not to be copied by any group or person in any manner without the

consent of Inspur Company. The Inspur Company reserves the right of revise this manual

momentarily.

Any alteration about the content of this manual will not be noticed. We suggest that the user

shall read this manual before using Inspur storage system, so as to avoid any mistake during

operation.

Please forgive any insufficiency in details, point out and give directions for us in time.

Please contact Inspur Group Company, if you have any questions or advice about this

manual.

Inspur

Nov. 2013

“Inspur ” is a registered trademark of the Inspur Group Co., Ltd.

Other trade marks belong to other corresponding registered companies.

Summary of Contents for AS500H

























































Search results

Summary of Contents for AS500H

Reviews:

Related manuals for AS500H

Brands by name

Popular brands

Inspur AS500H, User Manual

Search results

Summary of Contents for AS500H

Reviews:

Related manuals for AS500H

Brands by name

Popular brands