manualshive.com logo in svg

Inspire SLEEP REMOTE, Manual

Share
Download
Inspire SLEEP REMOTE Manual Download Page 61

Inspire Sleep Remote

English 47

You do not feel 
stimulation 
immediately 
when turning 
therapy on.

• Therapy may not 

have turned on.

• Pick up or gently shake the 

sleep remote to check therapy 
status. If the status ring is 
white, therapy is off. Turn 
therapy on again.

• Your stimulation 

may be delayed 
or paused.

• Pick up or gently shake the 

sleep remote to check therapy 
status. If the status ring is 
slowly dimming and 
brightening green, therapy is 
on and stimulation is paused. 
Stimulation will automatically 
start after the Start Delay or 
pause time.

• The stimulation 

strength may be 
set too low.

• Pick up or gently shake the 

sleep remote to check therapy 
status. If the status ring is solid 
green, stimulation is on. You 
may want to increase the 
stimulation strength (refer to 
page 28). If you still do not feel 
stimulation, contact your 
doctor.

• Your generator 

may need 
attention from 
your doctor.

• Pick up or gently shake the 

sleep remote. If the generator 
status light (

) on the back of 

the sleep remote is on, contact 
your doctor.

If this happens: Possible 

causes:

Try these steps:

Summary of Contents for SLEEP REMOTE









































































Reviews:

No comments

Brands by name

Popular brands

Load more brands