WARNING
Do not install or operate this fire-
place through a switch wired in the
120 VAC or 240 VAC circuits. The
only approved wiring for a switch
is through the low voltage circuit
(24 VAC) as shown on
Page 14
.
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
3
CONGRATULATIONS!
In selecting this Merit Plus electric fireplace, you have chosen the finest
most dependable fireplace found anywhere. A beautiful and prestigious addition to
the finest homes. Welcome to a Family of hundreds of thousands of satisfied
Fireplace Owners.
Please read and carefully follow all of the instructions found in this manual. Please
pay special attention to the safety instructions provided in this manual. The instruc-
tions included here will assure that you have many years of dependable and enjoyable
servfice from your product.
TAbLE OF CONTENTS
Important Safety Information ............Page 2
Packaging List . . ...............................Page 3
Introduction . . ..................................Page 3
General Information . . ......................Page 3
Locating Fireplace . . .........................Page 3
Tools/Supplies Required . . ...............Page 3
Framing Specifications . . ..................Page 4
Fireplace Specifications . . .................Page 4
Clearances . . ....................................Page 5
Pre-installation . . ..............................Page 5
Installation Steps . . ..........................Page 5
Electrical Connections .......................Page 5
Final Finishing . . ...............................Page 6
Break-In Period . . .............................Page 6
Control Panel Operation ....................Page 6
Remote Control Operation . . ............Page 7
Maintenance . . ..................................Page 8
Wiring Diagrams . .............................Page 9
Troubleshooting . ..............................Page 14
Replacement Parts . ..........................Page 15
Optional Accessories . .......................Page 17
Installation must conform to local codes.
In the absence of local codes, electrical
wiring and grounding must comply with
the National Electrical Code ANSI/ NFPA
70 - latest edition. In Canada, the current
CSA C22-1 Canadian Electrical Code -
latest edition.
GENERAL INFORMATION
Power Supply Wire Specifications
120 Volt, 60 Hz, 1600 Watts:
(ref.
Page 9)
Hard Wire Connection - Use two conductor,
non-metallic sheath cable with ground wire
(total three wires) for the incoming power
supply. The wire used must conform to local
and national electrical codes for the specified
power consumption rating. See Table 1.
240 Volt, 60 Hz, 3000 Watt:
(ref.
Page 10)
Use three conductor, non-metallic sheath cable
with ground wire (total four wires) for the
incoming power supply. The wire used must
conform to local and national electrical codes
for the specified power consumption rating.
See
Table 1
.
Wall Switch or Wall Thermostat Kits
(optional kits, see
Page 17)
Low voltage wire is provided for the wall switch
connection. The wires gage requirements are
shown on
Table 1
.
Figure 1
LOCATING yOUR MERIT ELECTRIC
FIREPLACE
Your new fireplace may be installed into existing
framing or built into a wall (see
Figure 1)
.
When choosing a location for your new fire-
place, ensure that the general instructions are
followed. Also, for the best effect, install the
fireplace out of direct sunlight and away from
overhead lighting. See
Figure 1
.
fireplace shown in gray.
TOOLS AND bUILDING SUPPLIES
NORMALLy REqUIRED
TOOLS:
Phillips Screwdriver
7/16" Socket Drive
Hammer
Saw And/or Saber Saw
Level
Measuring Tape
Plumb Line
Electric Drill And Bits
Pliers
Square
Gloves
IMPORTANT NOTE: This fireplace system
is not difficult to install. However, in the
interest of safety, it is recommended that
the installer be a qualified or certified
“tradesman” familiar with commonly
accepted fireplace installation and safety
techniques as well as prevailing local
codes.
bUILDING SUPPLIES:
Framing Materials
Wall Finishing Materials
Caulking Materials
(noncombustible)
Top View Showing Approved
Room Locations of Fireplace
Power Supply Wire Gage
Voltage
Wire Gage
Fuse
120 V
14 GA.
15 AMP
240 V
14 GA.
20 AMP
Wall Switch / Thermostat Wire Gage
Voltage
Wire Gage
5 VOLTS
18 GAGE
Table 1
PACKAGING LIST
This assembled Electric Room Heater is
packaged with:
• One accessory package located in the
firebox, containing;
1. One Installation and Operation Manual.
2. One Warranty Certificate.
3. One Remote Control.
INTRODUCTION
This Electric Fireplace is designed for
residential applications to be framed in as
a zero clearance fireplace.
This appliance has been tested in accor-
dance with UL 2021 and CSA C22.2 No.
46-M198 standards for fixed and location
dedicated electric room heaters.
