Innovate LM-2 User Manual Download Page 16 | Manualshive

Page: 16 / 51

background image

Document # 31-0008

LM2_Manual_1.4.doc

16

6. Select the firmware file with the dld extension.
7. The software will now prompt you to put the LM-2 in “Boot Mode.” In order to

accomplish this you must power the unit off. Next, while pressing the

Mode

button on the LM-2, power the unit back ON. The LM-2’s display will show that it
is now in “Boot Mode.” Press the OK button on the software to start the firmware
reflash.

8. Do not disconnect the unit from the computer until the firmware progress screen

completely disappears. Once finished you may disconnect the unit from the
computer and exit out of the software.

Note: Performing a firmware upgrade to the LM-2 clears all calibration data. The
LM-2 will perform a sensor calibration on the next power up after the firmware
upgrade. Be sure to have the O2 sensor outside of the exhaust (free air.)

3.3 Downloading Logs from Memory Card

Note: An SD memory card reader is necessary to retrieve logs from the memory card.
The logs can not be downloaded through the LM-2..

1. Remove the memory card from the LM-2 and insert it in your SD memory card

reader.

2. Launch LogWorks 3. The LogWorks 3 application can be launched from

Start-

>Programs->LogWorks3->LogWorks3

from the Windows task bar.

3. Click on

File->Import/Download->Import LM-2 Log.

«
...
14
15
16
17
18
...
»

Summary of Contents for LM-2




















































Reviews:

No comments

Related manuals for LM-2

NUFLO Scanner 2000 microEFM

Brand: Cameron Pages: 8

Brand: Danfoss Pages: 6

Brand: Quantel Pages: 2

Brand: Vanguard Instruments Pages: 24

Brand: Idexx Pages: 6

Brand: IDEAL INDUSTRIES Pages: 10

Brand: M-system Pages: 5

Brand: janitza Pages: 12

Brand: janitza Pages: 84

Brand: janitza Pages: 6

Brand: janitza Pages: 14

Brand: janitza Pages: 98

Clavinova CVP-601

Brand: Yamaha Pages: 98

Brand: Yamaha Pages: 28

Brand: Lasertec Pages: 21

Brand: janitza Pages: 128

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: Toro Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands