Innovate LM-2 User Manual Download Page 13 | Manualshive

Page: 13 / 51

background image

Document # 31-0008

LM2_Manual_1.4.doc

13

2.3 Calibration Schedule

Normally aspirated (daily driver)

- Calibrate before installation of new sensor
- Calibrate new sensor again after 3 month of use
- Thereafter calibrate once a year or every 20,000 miles, whichever comes first

Turbo Application, daily driver (tuned rich)

- Calibrate before installation of new sensor
- Calibrate new sensor again after 3 month of use
- Thereafter calibrate twice a year or every 10,000 miles, whichever comes first

Race Application

- Calibrate before first installation of new sensor
- Calibrate once per race weekend
- For added sensor life we also recommend our optional double length bung (part
number 3764

Dyno use:

- Calibrate a new sensor
- Calibrate every 2-3 days, depending on usage

«
...
11
12
13
14
15
...
»

Summary of Contents for LM-2




















































Reviews:

No comments

Related manuals for LM-2

Mentor Visual iQ

Brand: GE Pages: 2

Brand: E Instruments Pages: 2

Brand: Magnum Energy Pages: 3

Kotron 805 series

Brand: Magnetrol Pages: 36

Brand: Magnescale Pages: 104

Brand: Magnescale Pages: 44

Brand: Parkside Pages: 120

LaserHybrid SB 360i

Brand: Fronius Pages: 104

Brand: WATERGUARD Pages: 2

Brand: Omicron Pages: 76

Brand: Galileo Pages: 30

Brand: Hanna Instruments Pages: 15

Brand: horiba Pages: 10

Brand: Kane Pages: 36

Brand: Major tech Pages: 16

Brand: AEMC Pages: 16

Brand: Solight Pages: 2

Brand: geo-FENNEL Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands