INHECO HeatPAC User Manual Download Page 4

INHECO

04

Doc ID: 900372-002

October 2018

IMpOrtaNt NOtEs

1.1. 

General Information

Read the user instructions completely. The manual explains how to operate and handle 

the HeatPAC (7900046). In case manual instructions are not followed, injury or product 

damage cannot be excluded.

Missing or insufficient knowledge of the manual leads to loss of liability against  

INHECO GmbH.

This manual is part of the HeatPAC and must be retained until the device is disposed of 

and must be passed on with the HeatPAC when the device is taken over by a new user. 
The HeatPAC meets the acknowledged rules of technology and comply with today‘s 

standards.
Manual instructions must be followed in order to ensure safe handling of the device.
Security-related warnings in this manual are classified into three hazard levels:

The signal word WARNING indicates hazards which – without precautionary 

measures – can result in serious injury or even death.

The signal word CAUTION indicates hazards which – without precautionary 

measures – can result in minor to moderate injuries 

The signal word NOTE stands for general precautionary measures that are to be 

observed to avoid damaging the device when using it.

The signal word NOTICE stands for necessary measures that should be followed to 

avoid damaging the device when using it.

Contact INHECO in case there are any uncertainties of how to operate or how to handle 

the HeatPAC.
Your opinion about this manual provides us with valuable insights on how we can 

improve this document. Please do not hesitate to direct your comments to  

[email protected], → How to contact INHECO, page 5.

1.2. 

Explanation of symbols

Symbol

Explanation

Potential danger of serious injury or death → 

 

signal word WARNINg or CAUTION  indicate the severity.

Caution: hot surface

·

Bullet points indicates an instruction.

-

Hyphens refer to enumerations.

indicates refer to and are mostly an active link

Summary of Contents for HeatPAC

























Reviews: