background image

23

( )

Book 22442552 (7/03)

COMPRESSOR OIL LEVEL

Check the compressor oil level gauge on the separator
tank when the machine is not running. Gauge will not
provide an accurate level with machine operating.

WARNING

Always position (or remove) jack for maximum

ground clearance before towing.

UTILITY PACKAGE SET--UP

(no running gear)

This unit must be located on vehicle bed to allow
access for normal servicing and maintenance.

The air going into the inlet grille must be relatively free
of oil, dirt, soot and other debris. It must be no more
than 10 degrees F. (5 degrees C) over the ambient
temperature.

A flexible mounting system is required between the

package and vehicle bed or frame to isolate the ma-

chine and prevent damage.

WATER COOLED ENGINE

CAUTION

Do not remove pressure cap from a HOT radiator.
Allow radiator to cool down before removing
pressure cap. Use extreme care when removing a
pressure cap from a liquid cooling system for the
engine. The sudden release of pressure from a
heated cooling system can result in a loss of
coolant and possible severe personal injury.

WARNING

NO SMOKING, SPARKS or OPEN FLAME near
fuel.

Summary of Contents for P110WIR































































Reviews: