background image

Introduction

RT-SVX50C-EN

Overview of Manual

Note:

One copy of this document ships inside the control 
panel of each unit and is customer property. It must 
be retained by the unit’s maintenance personnel.

This booklet describes proper installation, operation, and 
maintenance procedures for air cooled systems. 

By carefully reviewing the information within this manual 
and following the instructions, the risk of improper 
operation and/or component damage will be minimized.

It is important that periodic maintenance be performed to 
help assure trouble free operation. A maintenance 
schedule is provided at the end of this manual.

Should equipment failure occur, contact a qualified 
service organization with qualified, experienced HVAC 
technicians to properly diagnose and repair this 
equipment.

Copyright

This document and the information in it are the property of 
Trane, and may not be used or reproduced in whole or in 
part without written permission. Trane reserves the right 
to revise this publication at any time, and to make changes 
to its content without obligation to notify any person of 
such revision or change.

Trademarks

All trademarks referenced in this document are the 
trademarks of their respective owners. 

Revision Summary

RT-SVX50B-EN (23 Nov 2015)

Added 380V/60Hz Units.

Updated Model Number Description Section

WARNING

Proper Field Wiring and Grounding 
Required!

All field wiring MUST be performed by qualified 
personnel. Improperly installed and grounded field 
wiring poses FIRE and ELECTROCUTION hazards. To 
avoid these hazards, you MUST follow requirements for 
field wiring installation and grounding as described in 
NEC and your local/state electrical codes. Failure to 
follow code could result in death or serious injury.

NOTICE: 

Water Damage! 

Non-factory penetrations through the base of this unit 
are not allowed. Any penetration in the base of the unit 
may affect the water tight integrity of the unit and lead 
to water leaks into the conditioned space. Failure to 
follow instructions could result in equipment and 
property damage.

Summary of Contents for EAC180A

































Reviews: