manualshive.com logo in svg

INGAL ET-SS, Product Manual, Page: 26 / 36

Share
Download
INGAL ET-SS Product Manual Download Page 26

26

Release  07/19

ET-SS

Tangent End Terminal

STEP 10

Angle Strut Assembly (Posts 0-1)   

 PARTS

INSTRUCTIONS

BB

10001299 2 EA

1. Assemble all parts in the configuration & orientation shown above. 
2. It will be necessary to make a shallow valley/trough between Post 0 & 1 for the 

ET-SS Angle Strut (Part N) and ET-SS Anchor Angles (Part M), since a portion will 

be below the finished grade. 

3. Position the ET-SS Anchor Angles (Part M) onto Post 0 and place ET-SS Angle 

Strut on the non-traffic side with short leg down and fasten to Post 0 & 1 using 

shown hardware (Part R, S, X, BB). 

4. Tighten all threaded hardware to a snug position with an appropriately sized 

wrench or socket. 

X 

10007095 4 EA

R 

10007551 1 EA

M

10007544 2 EA

N

10007547 1 EA

S

10007092 1 EA

Use only Trinity Highway parts 
that are specified herein for the 
ET-SS System for assembling, 
maintaining, or repairing the ET-SS 
System. Do not utilise or otherwise 
comingle parts from other systems 
even if those systems are Trinity 
Highway systems.

WARNINGS

Ensure fully assembled ET-SS Anchor Post height (with ET-

SS  Anchor Angles) does not exceed 102mm above finished 

grade line. 

Note: Items below grade 

shown for clarity.

Summary of Contents for ET-SS





































Reviews:

No comments