manualshive.com logo in svg

INGAL ET-SS, Product Manual, Page: 21 / 36

Share
Download
INGAL ET-SS Product Manual Download Page 21

21

Release  07/19

ET-SS

Tangent End Terminal

STEP 5

3.81m System Rail Assembly (Post 3-8) 

 PARTS

INSTRUCTIONS

C

10007537 3 EA

1. Assemble all parts in the configuration & orientation shown above. 
2. Place all System Rail panels (Part C) on the traffic side of the posts and lap 

all System Rail panels in the direction of traffic as shown above using shown 

hardware. 

3. Tighten all threaded hardware to a snug position with an appropriately sized 

wrench or socket.  

T

10001300 6 EA 

U

10007550 24 EA

BB

10001299 30 EA

Use only Trinity Highway parts 
that are specified herein for the 
ET-SS System for assembling, 
maintaining, or repairing the ET-SS 
System. Do not utilise or otherwise 
comingle parts from other systems 
even if those systems are Trinity 
Highway systems.

WARNINGS

Do not place anything between any post bolt head and the 

ET-SS System Rail that would prevent the bolt from pulling 

through (i.e. no rectangular washers or delineators). 

Failure to follow this warning could result in serious injury 

or death in the event of a collision. 

Summary of Contents for ET-SS





































Reviews:

No comments