background image

Installation Instructions

SP-WALLKIT-01

Visit the InFocus support site at www.infocus.com/support

9

3.

Install two 5/16-18 x 1/2" hex head cap screws (C) through
two 5/16" washers (K) and into holes on mounting bracket
and projector mount. (See Figure 11)

Figure 11

4.

Slide outer cover of mount (A) back against mounting
bracket. (See Figure 11)

5.

Install two #8-32 x 3/4" Phillips pan machine screws (F)
through holes on sides of outer cover. (See Figure 12)

Figure 12

Projector  Installation

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment!  It is the
installer’s responsibility to make sure the combined weight of
all components attached to the short throw projector mounts
up to (and including) the projector does not exceed 25 lbs
(11.34 kg) for the SP-WALLKIT-01.

Figure 13

Projector Mount Installation

1.

Line up mounting holes on projector mount (V) with
corresponding holes on mounting plate. (See Figure 13)

2.

Install four #10-24 x 1 3/8" Phillips pan machine screws (G)
through projector mount holes and into mounting plate.
(See Figure 14)

IMPORTANT ! :

If projector mount is NOT installed in the

same direction as shown in Figure 14, ROLL adjustment
screws will be inaccessible!

Figure 14

4

(K) x 2

(C) x 2

3

cover

(F) x 2

5

(bottom view)

holes for projector mount

mounting plate

(V)

(G) x 4

2

roll adjustment screws

Summary of Contents for SP-WALLKIT-01

















Reviews: