1
Chapter I Precautions
The IP domes have been designed and manufactured to ensure
maximum reliability for various applications. However, the actual
performance may also depend on how you plan and make the
installation. Before attempting to install or operate the IP domes,
therefore, please thoroughly familiarize yourself with the following
instructions, and make sure that they are strictly followed.
1.1 Be Careful During Transportation
To avoid damage, protect the units against extremes of pressure,
shock or vibration during transportation. The products must be
shipped in parts disassembled as the original packing did, and kept
away from water, fire and high magnetic radiation. In no event will
Infinova be liable for any damage or loss arising from improper
transportation or storage.
1.2 Plan Your Installation Beforehand
z
Do not install an indoor dome in outdoor environment.
z
Keep the domes away from electric or magnetic fields. Devices
such as TV, audio speaker, high-capacity transformer, electric
motor and radio transmitter usually generate magnetic fields that
may distort the camera images.
z
Protect the domes from dampness and dust. Do not install the
domes where the humidity is over 90%, or where there is greasy
smoke, steam, or too much dust.
z
Avoid installations in a hostile environment. The domes are
designed to work at a temperature ranging from -10
o
C to +60
o
C
(indoor) or -40
℃
to +60
℃
(outdoor).
1.3 Pay Extra Care During Installation
z
Handle the unit carefully, and do not drop or subject it to strong
shock or vibration.
z
Always use proper safety equipment for the location and
installation.
z
Make sure that the materials are capable of supporting four times
the maximum specified load.
z
The unit contains electrostatic-sensitive components. Be careful
not to touch any exposed circuits directly when connecting wires
and assembling the domes. It is recommended to use proper
static-proof equipment when handling the PCB.
z
Make sure that the domes are powered off when connecting wires
to avoid accident during installation.
z
Do not directly touch the lower dome bubble. The dome bubble
is a precision component, and any scratch could result in a
degradation of image quality.
z
Make sure that no metal objects or flammable substance
accidentally get inside the domes to avoid damage caused by
short circuit or fire.
1.4 Take Necessary Cautions for Electrical Safety
z
Always conform to local electrical safety codes when installing
or operating the domes.
z
When powering the domes and the auxiliary devices connected,
check that the power supply specifications correspond to those
required.
z
Keep the domes and communication cables at least 165 ft. (50 m)
away from high voltage equipment or cables. If a particular
installation requires closer wiring, shield the communication
wires with steel tube, and make it properly grounded.
z
In certain circumstances, the following measures are necessary
for electrical safety:
z
When making outdoor installation, route cables under eaves
whenever possible.
z
Do not use trolley wire in open area. Instead, place cables in steel
tubes that are properly shielded underground.
z
Be sure to install extra strong lightning proof equipment where
strong thunderstorms are frequent or where there is a high faradic
facility (e.g., a high voltage transformer substation) nearby.
1.5 Ensure Proper Operation and Maintenance
z
Protect the domes from excessive light. Do not point the domes
directly at such extremely bright light sources as the sun.
Otherwise, the CCD might be permanently damaged.
z
Do not dissemble the dome drive module. There are no user
serviceable parts inside the module, and failure to observe this
instruction will cause loss of warranty. For internal settings and
repairs, please refer to authorized personnel only.
z
The dome bubble should be cleaned periodically to get clear and
crisp images. Clean the dome bubble with a soft cloth, and be
careful to hold its edge only. Do not directly touch the dome
bubble. Any finger marks or scratches on the cover might cause
vague or distorted images.
z
Do not use chemical products like benzine or thinner. If neutral
cleanser is required, make sure to read all accompanying
instructions to determine that no negative effect will be caused.
z
Prevent any plastic or rubber material from staying in contact
with the cabinet for a long period of time. Otherwise, it might
cause paint peeling or damages.
