Infiniton 8436546191469, Instruction Manual

Page: 27 / 52

11
9
Fig.6
Hook position for Hook position for Hook position for
H=30mm
top
H=40mm
top
H=20mm
top
N.B:
Use the hook contained in the "accessories set"
f) In the event the cooktop is not installed above a built-in oven, a wood panel must be inserted as insulation.
This panel must be placed at least 20 mm from the bottom of the cooktop itself.
lmportant:
When installing the hob above a built-in oven, the oven should be placed on two wooden
strips; in the case of a joining cabinet surface, remember to leave a space of at least 45 x 560 mm at the
back.
When installing on a built-in oven without forced ventilation, ensure that there are air inlets and outlets for
ventilating the interior of the cabinet adequately.
Cuando instale sobre un horno empotrado sin ventilador forzado, asegúrese que en el interior del
gabinete hay entradas y salidas de aire.
10
Gas connection for gas hob
The Cooker should be connected to the gas-supply by a corgi registered installer. During installation of this
product it is essential to fit an approved gas tap to isolate the supply from the appliance for the convenience
of any subsequent removal or servicing. Connection of the appliance to the gas mains or liquid gas must be
carried out according to the prescribed regulation in force, and only after it is ascertained that it is adaptable
to the type of gas to be used. If not, follow the instructions indicated in the paragraph headed "Adaptation to
different gas types". In the case of connection to liquid gas, by tank, use pressure regulators that conform to
the regulation in force.
Important:
For safety, for the correct regulation of gas use and long life of the appliance, ensure that the
gas pressure conforms to the indications given in table 1 "Nozzle and burner characteristics".
Connection to non-flexible tube
(copper or steel)
Connection to the gas source must be done in such a way as to not create any stress points at any part of
the appliance.
The appliance is fitted with an adjustable, "L" shaped connector and a gasket for the attachment to the gas
supply.
Should this connector have to be turned, the gasket must be replaced (supplied with the appliance).
The feeding connector of the gas to the appliance is threaded 1/2 gas male cylinder.
Connection to flexible steel tube
The gas feed connector to the appliance is a threaded, male 1/2" connector for round gas pipe. Only use
pipes and sealing gaskets that conform to the standards currently in force. The maximum length of the
flexible pipes must not exceed 2000 mm. Once the connection has been made, ensure that the flexible
metal tube does not touch any moving parts and is not crushed.
Check the Seal
Once the appliance has been installed, make sure all the connections are properly sealed, using a soapy
water solution. Never use a flame.
Electrical Connection
The cooktops fitted with a tripolar electrical supply cord are designed to be be used with alternating current
according to the indications on the rating plate located under the cooktop. The earthing wire can be
identified by its yellow-green colour.
In the case of installation over a built-in electric oven, the electrical connections for the cooktop and oven
should be independent, not only for safety purposes, but also to facilitate removal of one or both in the
future.
Electrical Connection for Gas Cooktop
Fit the supply cord with a standard plug for the demand rate indicated on the rating plate or connect it
directly to the electrical mains. In the latter case, a single pole switch must be placed between the appliance
CONEXIÓN DE GAS PARA LA UNIDAD
Conexión de gas para cocinar con gas
La unidad debe ser conectada al suministro de gas por un instalador certificado. Durante la instalación
de este producto es esencial adaptar un grifo de gas aprobado para aislar el suministro del aparato con
el fin de facilitar cualquier posterior remoción o mantenimiento. La conexión de la unidad a la red de gas
o gas lí
quido debe ser llevada a cabo de acuerdo con la regulación que este actualmente en vigor, y
sólo después de que se determine que es adaptable al tipo de gas a utilizar. Si no es así , siga las
instrucciones indicadas en el párrafo "Adaptación a los distintos tipos de gas". En el caso de conexión
para gas lí
quido, por tanque, utilice reguladores de presión que se ajusten a la normativa vigente.
Importante!
Por razones de seguridad, para la correcta regulación del uso del gas y para alargar la vida útil de la
unidad, asegúrese que la presión del gas se ajusta a las indicaciones dadas en la tabla 1
"Especificación de los quemadores y boquillas".
CONEXIÓN AL TUBO NO FLEXIBLE
(Cobre o acero)
La conexión a la fuente de gas debe hacerse de tal manera que no cree ningún punto de tensión en
cualquier parte de la unidad.
Esta unidad está equipada con un conector ajustable en forma de "L" y una junta para la fijación al
suministro de gas.
En caso de que este conector tenga que ser convertido, debe ser reemplazada la junta (suministrada
con el aparato).
El conector de alimentación de gas al aparato es un cilindro macho de gas de ½ roscado.