Inficon D-TEK Stratus 724-202-G Series Operating Manual Download Page 13 | Manualshive

Page: 13 / 35

background image

INFICON

Charging the Battery | 7

074-708-P1A D-TEK Stratus OM

13 / 35

7 Charging the Battery

D-TEK Stratus uses a rechargeable lithium ion battery that comes partially charged.

INFICON recommends charging the battery before use. Using the supplied charger or

charging cradle accessory, a dead battery can be charged to 80% in approximately 2

hours and 100% in approximately 3 hours. A full charge typically lasts about 8 to 10

hours of operation, depending on the mode used and the operating temperature. An

on-screen indicator displays the remaining battery percentage.

D-TEK Stratus can be used while charging.

«
...
11
12
13
14
15
...
»

Summary of Contents for D-TEK Stratus 724-202-G Series




































Reviews:

No comments

Related manuals for D-TEK Stratus 724-202-G Series

Brand: Zipato Pages: 2

Brand: X2 Digital Wireless Systems Pages: 16

Vingtor Stentofon SPA-AC6

Brand: Zenitel Pages: 54

Brand: Abus Pages: 124

Brand: Polaroid Pages: 73

NVIP-2H-6602-II

Brand: Novus Pages: 40

Brand: Texecom Pages: 15

Brand: teko Pages: 4

Brand: United Vision Solutions Pages: 53

Brand: Ganz Pages: 4

Stealth STL110H

Brand: RAB Lighting Pages: 31

Brand: jablotron Pages: 2

Brand: P&E Pages: 2

Brand: INSTEON Pages: 17

Brand: Optigene Pages: 68

Brand: Vivotek Pages: 12

Interlogix RF430I4

Brand: United Technologies Pages: 4

Brand: TRASSIR Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands