Inficon D-TEK Stratus 724-202-G Series Operating Manual Download Page 29

Page: 29 / 35

INFICON

Replacement Parts and Accessories | 21

074-708-P1A D-TEK Stratus OM

29 / 35

21 Replacement Parts and Accessories

replacement carrying case

724-700-G1

earbuds

721-607-G1

12 V (dc) car charger

721-605-G1

AC wall charger (includes plugs for

multiple regions)

721-606-G1

lithium ion battery

721-702-G1

battery charging cradle

721-610-G1

battery/charging cradle combination

721-604-G1

standard sensor (detects CFCs, HCFCs,

HFCs, HFOs, and blends (including

A2Ls))

724-701-G1

sensor

724-701-G2

filter cartridges (quantity, 5)

712-707-G1

replacement probe cap

712-705-G1

needle probe extension

721-612-G1

extra-long probe

721-611-G1

TEK-Check R134a test leak

703-080-G10

Summary of Contents for D-TEK Stratus 724-202-G Series




































Search results

Summary of Contents for D-TEK Stratus 724-202-G Series

Reviews:

Related manuals for D-TEK Stratus 724-202-G Series

Brands by name

Popular brands

Inficon D-TEK Stratus 724-202-G Series, Operating Manual

Search results

Summary of Contents for D-TEK Stratus 724-202-G Series

Reviews:

Related manuals for D-TEK Stratus 724-202-G Series

Brands by name

Popular brands