background image

ATTENTION!!

Read this manual carefully  before installing the C ard Reader!

M ains connection

C hanges and/or  mdodifications

Secur ity

Before connecting the appliance to the mains, check that the mains supply  v oltage corresponds
to the v oltage printed on the ty pe plate of the adapter. If the mains v oltage is different, consult
y our supplier.

C hanges and/or modfications w hch hav e not been approv ed by  the responsible party  can v oid
the user's authorty  to operate the equitement.

A lw ay s disconnect the pow er supply  before handling any thing inside the dev ice.

This dev ice is complies w ith part 15 of the F C C  rules, operation is subject to tw o conditions:
(1) This dev ice may  not cause harmful interference.
(2) This dev ice must accept any  interference receiv ed, includng interference that may  cause
undesired operation.

FC C  Feder al C ommunications C ommission - US

End of life dir ectives

Inepro is pay ing a lot of attention to env ironmentally -friendly  production. Your new  dev ice contain
materials w hich can be recy cled and reused. A t the end of its life specialised companies can
dismantle the discarded dev ice to recy cle the reusable materials and to minimise the amount of
materials to be disposed of. P lease observ e the local regulations regarding the disposal of
packaging materials, exhausted batteries and old equipment.

This dev ice may  only  be used indoors.

Indoor  User  O nly

Directives

I

This dev ice is in conformity  w ith the E M C  directiv e and low -v oltage directiv e.

C E C onfor mité Eur opeène ( C onfor m Eur opean Nor m)

Guar entee

N o guarantee can be giv en if safety  regulations are not follow ed.

A ppareil concernés:
M C R708, M C R708G , D C R708, D C R708G

Le présent appareil est conforme aux C N R
d’Industrie C anada applicables aux appareils radio
exempts de licence.
L’exploitation est autorisée aux deux conditions
suiv antes :
(1) l’appareil ne doit pas produire de brouillage, et 

 

(2) l’utilisateur de l’appareil doit accepter tout

brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le
fonctionnement.

C onfor mité d’Industr ie C anada

Relev ant D ev ices:
M C R708, M C R708G , D C R708, D C R708G

This dev ice complies w ith Industry  C anada’s
licence-exempt RS S s. O peration is subject to the
follow ing tw o conditions:
(1) This dev ice may  not cause interference; and
(2) This dev ice must accept any  interference, including
interference that may  cause undesired operation of the
dev ice.

C onfir m C anada Industr ies

Summary of Contents for IP Card Reader















































Reviews: