1 / 3
+
-
AirSOU-100NB
02-26/2018 Rev.: 0
1
4
5
8
5
3
7
2
9
10
6
2
1
5
Click!
3a
4
+
-
ELKO EP, s.r.o.
Palackého 493
769 01 Holešov, Všetuly
Czech Republic
Tel.: +420 573 514 211
e-mail: [email protected]
www.elkoep.com
Characteristics
EN
Twilight sensor
Made in Czech Republic
• Information about the actual light intensity can be used in the task of maintain-
ing a constant illumination in a given space, where it is possible to regulate the
intensity of artifi cial lighting thanks to the contribution of natural lighting from
outside, thereby reducing the energy consumption.
• AirSOU-100 can be used not only in residential projects, but also in commercial
offi
ce projects or production and warehouse or production halls.
• The AirSOU-100 is recommended to be installed so that the light sensing sensor is
facing downwards and not exposed to direct light.
• The scanning range is 1 - 100,000 lux.
• Data is sent to the server from which it can be subsequently displayed as a smart-
phone, application, or Cloud notifi cation.
• Battery power can be sent to the server when it is powered by a battery.
• The AirSOU-100 is supplied in an IP65 enclosure and can be installed in an out-
door environment.
Device description
1. Tamper
2. NanoSIM slot
3. Programming pins
4. Button SET
5. Mounting hole Ø 4.3mm wall
6. Sensing sensor
7. Light guide
8. Antenna
9. Battery
10. LED
Cloud app assignment
It is done in your Smartphone application. Enter the relevant information on the product
cover into the application.
Function
After inserting the batteries, the sensor sends an introductory message containing the
measured light intensity.
The sensor scans the light intensity every 2 minutes. After that, it sends a data message
of measured values every 60 minutes. In the event of a sudden change in light intensity,
it sends the data message immediately.
General instrucions
Assembly
1. Using a fl at-blade screwdriver gradually slide it into one groove and the other in the lid
and swing open the cover.
2. Carefully insert nanoSIM (the device must not be energized when inserting or replacing
nanoSIM!)
3. The product can be attached in two ways:
a) Directly on a fl at surface by gluing * - apply a suitable adhesive to the bottom of the
base. Place the base in the desired location and let it dry.
b) Using a suitable fastener ** by screwing - drill holes into the base with two holes of
suitable diameter corresponding to the position of the holes in the bottom of the box.
Place the base at the desired location and attach it with suitable bonding material
according to the substrate.
4. Insert the battery into the sensor and check correct location (the sensor functionality
message is sent to the application when the battery are inserted).
5. Replace and snap the front cover. When closing, the handles have to be snapped to their
original position.
* The glue must meet the optimal conditions for product placement (infl uence of tem-
perature, humidity ...)
** For example, a screw or screw of max. Ø 4 mm can be used as a suitable fastener mate-
rial, 13 mm (distance to the partition in the box) must be added to the required length
for attachment to the substrate.
Internet of Things (IoT)
• The IOT wireless communications category describes the Low Power Wide Area
(LPWA). This technology is designed to provide full-range coverage both inside and
outside buildings, energy-saving and low-cost operation of individual devices. The
NarrowBand network is available to use this standard.
Information about the NarrowBand network
• The network provides two-way communication and the only one to use the licensed
LTE band. Our devices allow band 1 (2100MHz), Band 3 (1800MHz), Band 8 (900MHz),
Band 5 (850MHz), Band 20 (800MHz) and Band 28 (700MHz).
• It uses this SIM card technology for each device.
• The advantage of NarrowBand is the use of already built-up grids, which ensures suf-
fi cient reception outside and inside buildings.
• For more information on this technology, please visit www.vodafone.cz
Caution for proper operation:
• Products are installed according to the wiring diagram given for each product.
• For proper device functionality, it is necessary to have suffi
cient coverage of the se-
lected network at the installation site.
• At the same time, the device must be registered in the network. Successful device reg-
istration on a given network requires a charge for traffi
c.
• Each network off ers diff erent tariff options - it always depends on the number of mes-
sages you want to send from your device. Information on these tariff s can be found in
the current version of the ELKO EP pricelist.
