P. I. E. INEL Sp. z o. o., ul. Mostowa 1, 80-778 Gdańsk, [email protected]
www.inel.gda.pl
2.3
Electrical connections
A
monostable switch
can be connected to the motor, which will
short the control signal (black wire) with ground (grey wire) when
pressed.
The switch operates in a loop: up - stop - down - stop.
DISCONNECT POWER SUPPLY BEFORE MAKING
ANY CONNECTIONS!
Improper roller blind installation will cause the
motor to stop unexpectedly.
In order for the obstacle detection drive to function properly,
the following is required:
1. Use a special driver provided with the motor (figure 2-E)
2. Ensure that the curtain can move freely in the guides and
the cassette. This movement may not be obstructed (e.g.
by increase of the roller blind cassette temperature,
mosquito net etc.)
3.
REGISTERING REMOTE CONTROLS
The motor is compatible with the following remote controls: PIL-
01/04NS, 01/05/09/19PM, PIL-19/99PMT, PIL-01/05/09/19DL,
PIL-19/99DLT, PIL-01PT.
Our drives allow for two methods of entering the remote control
registration mode:
3.1. Each time after connecting to mains each drive will
enter the registration mode for 10 seconds.
After the motor is received from the manufacturer or if the
remote control is lost, a new remote can be registered as
follows:
Connect the drive to the mains: 230 VAC. The motor will make
two up-down movements. Within 10 seconds from connecting
to the mains, press the ▲ and ▼ buttons on the remote control
at the same time for the selected channel
The drive will make a short up and down movement. Within the
next 10 seconds register the channel by pressing ▲.
The registration will be confirmed by a short up-down
movement.
WARNING: The procedure will erase all previously
registered channels from the memory. This will allow to
register a remote control with a drive without another
registered remote control (new drive or lost/stolen remote).
3.2. Entering the registration mode with a previously
registered remote control.
If a remote control has already been registered, subsequent
channels of the same or another remote can be registered
without disconnecting from the mains. On the registered
remote,
press the ▲ and ▼ buttons at the same time.
The roller blind will move up and down. It will remain in
registration mode for the next 10 seconds. During that time, in
order to register a new channel of the same or another remote,
select the desired channel on the remote and press the ▲
button.
This way you can register any channel to any drive, but only if
you have a previously registered remote control.
4.
INVERTING MOVEMENT DIRECTION
If you need to invert the movement of the roller blind (roller blind
movement direction does not match the directions on the
remote control), you must enter programming mode (with a
previously registered remote).
Press the ▲ and ▼ buttons on the remote at the same time, the
motor will make a short up-down movement, then press STOP,
the motor will make another short up-down movement. Press ▲
and ▼ again, and then STOP, the motor will move up-down-
down-up.
WARNING: Changing motor direction will delete limit
positions.
5.
PROGRAMMING
In the factory mode and during limit position set-up the drive
will move with a 1-second pause immediately after start - this
means that no limit positions have been set.
5.1. BEFORE PROGRAMMING
A. Check whether the direction of roller blind movement
matches the buttons on the remote control (if they are
opposite, use the remote to switch them around). See
section 4.
B. Place the lower edge of the curtain at half the height of
the guides. Starting the programming procedure too
near the roller blind cassette may damage it.
WARNING! Programming always starts with the set-up of
the upper limit.
5.2. AUTOMATIC LIMIT PROGRAMMING
The programming procedure may be performed
automatically only if blocking hangers and stoppers are
used, and a sill is mounted in the window. The length of the
curtain must be adjusted to the length of the guides.
1. Press and release the "
↑
" button on the remote, the
drive will move upwards.
2. At the top, the drive will stop on the stoppers, after 3
seconds it will set the upper limit and switch movement
direction. At the bottom the drive will stop as soon as it
reaches the sill and set the lower limit, after which it will
Before drive startup/programming check the condition of
the curtain, guides and roller blind cassette and whether
there is a sill mounted in the window!
The roller blind cassette and guides should be free from
any contaminants and ensure unrestricted curtain
movement throughout the entire length. If the guides are
contaminated with building materials or are too tight, they
can cause damage to the drive and the roller blind, which
is not covered by the warranty.
Figure 3
N - neutral
PE - protective
L -
brown
yellow-green
black
blue
grey
