manualshive.com logo in svg

Incon 1250B, Installation And Programming Manual, Page: 34 / 36

Share
Download
Incon 1250B Installation And Programming Manual Download Page 34

34 

 

5.0

 

Error Codes 

 

Table 5.1 Error Codes 

DISPLAY  DESCRIPTION 

FA 2

 

Watchdog Re-start (Processor Crash)  If the condition recurs, call Technical 
Service.

 

FA 3

 

Memory Error at start-up    
(User programming is erased; Factory program defaults are re-loaded)

 

FA 5 

Keyboard Error at Start Up 
(Up or Down Key, or more than one key is being pressed during Power-Up) 

FA 20

 

Input Calibration Error (Input signal differential too large) 

FA 25 

Synchro input signal not present 

 

 

Err 5

 

Analog minimum position cannot be displayed with the number of left digits 
set.  (Increase number of left digits in OP 4) 

Err 6

 

Analog maximum position cannot be displayed with the number of left digits 
set.  (Increase number of left digits in OP 4) OR greater than 65,535 turns 
required to span Analog Min. to Analog Max.  (Increase counts per turn (OP 3) 
or reduce analog output span.) 

Err 7 

Low Relay limit position cannot be displayed with the number of left digits 
set.  (Increase number of left digits in OP 4) 

Err 8 

High Relay limit position cannot be displayed with the number of left digits 
set.  (Increase number of left digits in OP 4) OR limit not useable, greater than 
65,535 turns required to span between LO & HI relay limits (Increase counts 
per turn (OP 3) or reduce span between relay limits) 

Err 17 

Preset position cannot be displayed with the number of left digits set.  
(Increase number of left digits in OP 4)    OR   greater than 65,535 turns 
required to reach Analog Min. or Analog Max. from present position (increase 
counts per turn (OP 3) or reduce analog output span.) 

Err 30

 

Analog output calibration mode not enabled (Change OP 30 to “On”) 

Err 80 

 Wrong combination of serial port settings (Check parity, data & stop bits) 

 

 

TAb d

 

Non-Linear Table duplicate data point entered

 

TAb E

 

Non-Linear Table emptied 

 

 

TAb F

 

Non-Linear Table full (100 data point pairs max.) 

 

 

 

Flashing 

9’s

 

Display over-range (Increase number of left digits in OP 4)

 

 
 
 
 
 

Summary of Contents for 1250B





































Reviews:

No comments