manualshive.com logo in svg

Incon 1250B, Installation And Programming Manual, Page: 14 / 36

Share
Download
Incon 1250B Installation And Programming Manual Download Page 14

14 

Programming: 
 
OP 12 (tnS F)

 sets the 

Rotation Rate Threshold

 for the first filter.  If the synchro rotates 

slower than this number of 

degrees per second

, the measured positions will be accepted as 

valid synchro positions, and immediately displayed.  Synchro rotations faster than this rate 
will be ignored and assumed to be noise-induced aberrations.  When 

OP 12 (tnS F)

 is set to 

zero, this filter will be disabled.  The maximum value for this parameter is “3600.0”.  The 
Serial Command Line protocol for this parameter is: “

TURNSF_nnn.nn”

   

 

OP 13 (FLttH)

 sets the 

Turns Rate Threshold

 for the averaging filter.  If the synchro rotates 

slower than this number of 

display counts per second

, the second filter will be active and 

will average the position readings.  Synchro turns faster than this rate will cause the filter to 
temporarily stop averaging.  When 

OP 13 (FLttH)

 is set to zero, the averaging filter will be 

active at all times.  The maximum value for this parameter is “99999”. 
Serial Command Line protocol for this parameter is: “

FLTTH_nnn.nn”

   

 

OP 14 (FdPtH)

 sets the 

Depth

of the averaging filter.  The higher this number, the greater 

number of position samples will be averaged and the longer it will take for the display to be 
updated during a position change.  When 

OP 14 (FdPtH)

 is set to zero, this filter will be 

disabled.  The maximum value for this parameter is “128.0” 
The Serial Command Line protocol for this parameter is “

FDPTH_nnn.nn

”. 

 
 
 

Loss of Synchro Signal “FA 25” Error Code Reset 

 
The INCON model 1250B has Synchro Signal Loss detection firmware that freezes all 
outputs at their last known good positions, and displays an “FA 25” error code when the 
synchro signal is lost.  The 1250B has an item in the programming menu which allows the 
“automatic reset” portion of this feature to be enabled or disabled. 
 

Programming:

 

 
In the programming menu, there will be an item: “

OP 53

”, or its Alpha-Numeric equivalent: 

“

AUt25

”.  If this menu item is selected, the default value will be “

OFF

”, meaning that the 

error condition will not automatically reset (the MENU key will need to be pressed to 
manually reset the FA 25 error code).  This may be changed to “

On

” by pressing the UP or 

DOWN key.  With this menu item set to “

On

”, the error code will automatically reset as soon 

as the synchro signal is restored.  Press the ENTER key to store the selected setting. 
The serial commands to program this function are “

AUTO25 ON

” and “

AUTO25 OFF

”. 

 
 

IMPORTANT NOTICE:

 When the synchro signal is lost the 1250B will not detect if 

synchro rotation occurs.  When the synchro signal is restored, 

the 1250B may not be reading 

the correct position

.  All outputs (Analog, Relays, Serial,) which are driven by the displayed 

value may also be incorrect. 

Summary of Contents for 1250B





































Reviews:

No comments