background image

 
 

TABLE OF CONTENTS 

 

BEFORE YOU BEGIN......................................................................................  1 
IMPORTANT SAFETY NOTICES..................................................................... 2 
HARDWARE PACK……….....…....................................................................... 3 
ASSEMBLY INSTRUCTIONS........................................................................... 6 
WEIGHT RESISTANCE CHART........................................................................24 
PARTS LIST………………………………………………………………………….. 25 
WARRANTY.................................................................................................… 26 
ORDERING PARTS.........................................................................................  26

 

 
 

 
 
 
 
 
 
BEFORE  YOU  BEGIN 

 

Thank you for selecting the MARCY PLATINUM MP2100 by IMPEX INC.  For 
your safety and benefit, read this manual carefully before using the machine.   
As a manufacturer, we are committed to provide you complete customer 
satisfaction.  If you have any questions, or find there are missing or damaged 
parts, we guarantee you complete satisfaction through direct assistance from 
our factory.  To avoid unnecessary delays, 

please call our  TOLL-FREE 

customer service number.  

Our Customer Service Agents will provide 

immediate assistance to you.

 

 

 
 
 
 
 

 

Toll-Free Customer Service Number       

1-800-999-8899 

Mon. - Fri. 9 a.m. - 5 p.m.  PST 

www.impex-fitness.com 

[email protected]

 

Summary of Contents for MARCY PLATINUM MP 2100




























Reviews: