background image

1.INTRODUCTION:

Thank you very much for choosing our product. For your benefit and safety, please read the 
manual and follow the instructions carefully. You will certainly enjoy a great workout experience 
and a healthy body when you are well prepared after reading the manual.

2.SAFETY GUIDELINE

Ÿ

Always consult your physicians before starting your workout.

Ÿ

Read through the operation manual and follow the instruction when using the treadmill.

Ÿ

Keep children away from the treadmill at all times.

Ÿ

Keep the safety key out of the reach of all children.

Ÿ

Never start the treadmill without making sure all power cord is normal and with no damage.

Ÿ

Place the treadmill on a solid level surface with the rear and side away from any objects.

Ÿ

Keep your hands away from any moving parts.

Ÿ

Do not place any liquid near or on the treadmill.

Ÿ

Wear appropriate clothes and shoes during the workout; Do not wear any shoes that may 
damage the running belt;

Ÿ

Stop the workout immediately when you feel any discomfort; consult your physicians for 
advice.

Ÿ

Never start the treadmill while you are standing on the running belt; Stand on the foot rails to 
start.

Ÿ

If you have any questions or concerns, contact dealer.

Ÿ

Make sure the ground-wire is properly connected during assembly.

Ÿ

The treadmill is intended for in-home use only. Always exercise caution during the workout.

Ÿ

Clip the safety key to your clothes during the workout.

Ÿ

Hold onto the handrails or stand on the foot rails during any emergency, or step off the 
treadmill.

Ÿ

Contact your dealer for professional help if you have any question.

Ÿ

Place the treadmill on a level surface with enough clearance behind it, 2M is needed

,

 and on both 

sides of the treadmill is 0.6M

.

Ÿ

The optimal place to stand on the treadmill is at about 1/3 of the length of the running belt to the 
front of the treadmill. You might step on the motor cover if you stand too close to the front and 
crush the cover, or be tripped by the running belt. If you stand too close to the back of the running 
deck, you might not catch the speed and fall off.

Ÿ

The maximum weight allowed on this machine is 130kg. Warranty will not be honored when this 
advice is not carefully followed. 

This machine is not intended for use by persons (including children) with reduced physical, 
sensory or mental capabilities, or lack of experience and knowledge, unless they have been 
given supervision or instruction concerning use of the machine by a person responsible for their 
safety. Children should be supervised to ensure that they do not play with the machine.

3.MAINTENANCE:

A. Regular Maintenance:

a   Clean and lubricate the running deck after each 20-hour of use or on a monthly basis, which 

ever comes first (SEE TREADMILL LUBRICATION INSTRUCTIONS). Clean both sides of the 
running belt daily will prevent dirt from getting underneath the running belt.

b.  To keep the dust off, clean the treadmill both on the surface and beneath it; Place a mat under 

the treadmill to keep the dust off and to protect the floor.

c.  Keep the liquid from the monitor or the running belt.
d.  Contact your dealer for any service assistance.

3

Summary of Contents for iT 4500

















Reviews: