ImmersionRC vortex 250 pro Instruction Manual Download Page 48

Page: 48 / 65

Flight Controller Firmware Upgrades

To upgrade the Flight-Controller firmware, use the cleanflight-configurator:

1) Remove all Props!
2) Connect the Vortex to any PC/Mac/Linux machine which supports the Cleanflight

Configurator

3) Plug Lipo
4) Wait 10 seconds
5) Follow the standard upgrade instructions for Cleanflight (IRCFUSIONF3)

NOTE: Sometimes it may need few attempts before it starts flashing, so keep trying few
times if upgrade does not start

NOTE: Upgrading Cleanflight to a version not supported by the OSD firmware can easily
result in the OSD not functioning. Please refer to the Vortex product page on the
ImmersionRC website for compatibility information.

NOTE: When Vortex will detect a new flight-controller version, it will automatically restart
in TX Wizard mode.

Summary of Contents for vortex 250 pro


































































Search results

Summary of Contents for vortex 250 pro

Reviews:

Related manuals for vortex 250 pro

Brands by name

Popular brands

ImmersionRC vortex 250 pro, Instruction Manual

Search results

Summary of Contents for vortex 250 pro

Reviews:

Related manuals for vortex 250 pro

Brands by name

Popular brands