background image

14

C82

1-22

C42

C52

1-23

1-25

C82

1-24

4

6

5

1

3

2

7

8

5

9

7

A

S

INS

TALLER

US

ER

 MAINTEN

AN

CE TECHNI

CI

AN

1.12 SEPARATOR KIT INSTALLATION.

Type C configuration, sealed chamber and 

fan assisted.

This kit allows air to come in from outside 

the building and the exhaust to exit from the 

chimney or flue through divided flue exhaust 

and air intake pipes. Combustion products are 

expelled from pipe (S). The required amount of 

air is taken in through pipe (A) for combustion. 

The intake pipe (A) can be installed either on the 

right or left hand side of the central exhaust pipe 

(S). Both ducts can be routed in any direction.

• 

Separator kit Ø 80/80. 

Kit assembly (Fig. 1-22): 

install the flange (4) on the central hole of the 

boiler, interposing the gasket (1) and tighten 

with the flat-tipped hex screws included in the 

kit. Remove the flat flange present in the lateral 

hole with respect to the central one (according 

to needs) and replace it with the flange (3), 

positioning the gasket (2) already present in 

the boiler and tighten using the supplied self-

threading screws. Fit the male end (smooth) to 

the bends (5) in the female end of the flanges 

(3 and 4). Fit the intake terminal (6) with the 

male section (smooth) in the female section of 

the bend (5) up to the stop, ensuring that the 

internal and external wall sealing plates are 

fitted. Fit the exhaust pipe (9) with the male end 

(smooth) to the female end of the bend (5) up 

to the stop; making sure that the internal wall 

sealing plate has been fitted, this will ensure 

sealing and joining of the elements making up 

the kit.

• Installation clearances. Figure 1-23 gives the 

min. installation space dimensions of the 

Ø 80/80 separator terminal kit in limited 

conditions.

• Figure 1-24 shows the configuration with 

vertical exhaust and horizontal intake.

•  Extensions for separator kit Ø 80/80. The max. 

vertical linear length (without bends) usable 

for Ø 80 intake and exhaust pipes is 41 metres 

of which 40 intake and 1 exhaust. This total 

The kit includes:

 N°1  -  Exhaust gasket (1)

 N°1  -  Female intake flange (3)

 N°1  -  Flange gasket (2)

 N°1  -  Female exhaust flange (4)

 N°2  -  90° bend Ø 80 (5)

 N°1  -  Intake terminal Ø 80 (6)

 N°2  -  Internal wall sealing plates (7)

 N°1  -  External wall sealing plate (8)

 N°1  -  Exhaust pipe Ø 80 (9)

Maximum usable lengths

(including intake terminal with grill and two 90° bends) 

NON-INSULATED PIPE

INSULATED PIPE

Drain (metres)

Intake (metres)

Drain (metres)

Intake (metres)

1

36.0*

6

29.5*

2

34.5*

7

28.0*

3

33.0*

8

26.5*

4

32.0*

9

25.5*

5

30.5*

10

24.0*

*  The air intake pipe can be increased to 2.5 metres if the exhaust bend 

is eliminated, 2 metres if the air intake bend is eliminated, 4.5 metres 

eliminating both bends.

11

22.5*

12

21.5*

Attention:

 the boiler is designed to evacuate 

the combustion products up to a maximum 

extension of 27 linear metres from the exhaust, 

with 1 m plus 90° bend at the intake. If the 

installation requests a development of the flue 

to the discharge that exceeds the recommended 

12 m, due consideration must be given to the 

formation of condensate that could take place 

inside the pipe and Immergas insulated “Blue 

Series” flue kits must be used.

Summary of Contents for Mini Eolo 24 3 E





































Reviews: