background image

HV2-805R

WARNING: If the information in this manual is not followed
exactly, a fire or explosion may result causing property damge,
personal injury or loss of life.

Do not store or use gasoline or other flammable vapors and liquids
in the vicinity of this or any other appliance.

What to do if you smell gas:

• Do not try to light any appliance.

• Do not touch any electrical switch. Do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor's phone. Follow

the gas supplier's instructions.

• If you cannot reach your gas supplier, call the fire department.

Installation and service must be performed by a qualified in

staller,

service agency or the gas supplier.

DESIGNED AND TESTED ACCORDING TO A.S.M.E. 

BOILER AND PRESSURE

VESSEL CODE, SECTION IV

 FOR MAXIMUM ALLOWABLE WORKING PRESSURE OF

50 PSI

345 kPa WATER

NOTE TO INSTALLING CONTRACTOR:

 READ THESE INSTRUCTIONS CAREFULLY.

THEY WILL SAVE YOU TIME IN ASSEMBLING BOILER PROPERLY.

INSTALLER, THESE INSTRUCTIONS TO BE AFFIXED ADJACENT TO THE BOILER.

CONSUMER, RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE PURPOSES.

260 NORTH ELM STREET WESTFIELD, MA 01085
TEL. (413) 564-5515  FAX (413) 568-9613

WARNING: Installation and service must be performed by a qualified installer, service
agency or the gas supplier in accordance with all local and national codes. Failure to
comply with this warning can result in a fire or explosion causing property damage,
personal injury  or loss of life!

HV

NATURAL OR PROPANE GAS BOILER

INSTALLATION & OPERATING

INSTRUCTIONS

In Canada: 5211 Creekbank Road, Mississauga, Ont. L4W 1R3 (905) 625-2991  Fax (905) 625-6610

Summary of Contents for HV-100

























Reviews: